Maintenance And Care - Flex L 3403 VRG Originalbetriebsanleitung

Preselecting the speed
 To set the operating speed, move the dial
to the required value.
 Gently press the switch to accelerate the
power tool up to the preselected speed.
`^rqflk>
oáëâ=çÑ=áåàìêó=ÇìÉ=íç=ÇÉëíêìÅíáçå=çÑ=íÜÉ=íççäK=
rëÉ=íÜÉ=~ééêçéêá~íÉ=íççä=Ñçê=íÜÉ=àçÄK
klqb
fÑ=~å=çîÉêäç~Ç=çê=çîÉêÜÉ~íáåÖ=çÅÅìêë=ÇìêáåÖ=
ÅçåíáåìÉë=çéÉê~íáçåI=íÜÉ=éçïÉê=íççä=
~ìíçã~íáÅ~ääó=êÉÇìÅÉë=íÜÉ=ëéÉÉÇ=ìåíáä=íÜÉ=
éçïÉê=íççä=Ü~ë=ÅççäÉÇ=Ççïå=~ÇÉèì~íÉäóK
Attaching the tool holder
 Pull out the mains plug.
 Press and hold down the spindle lock (1.).
 Screw the tool holder (Velcro pad, fleece
pad) clockwise onto the spindle and tighten
hand-tight (2.).
 Attach the tool to the tool holder.
 Insert the mains plug into the socket.
 Switch on the polisher (without engaging it)
and run the polisher for approx. 30 seconds.
Check for imbalances and vibrations.
 Switch off the polisher.
18
Changing the tool holder
 Pull out the mains plug.
 Press and hold down the spindle lock.
 Unscrew tool holder anti-clockwise and
screw it off the spindle.
 Attach new tool holder (see above).
Attaching the tools
`^rqflk>
^íí~ÅÜ=íÜÉ=íççäë=áå=íÜÉ=ÅÉåíêÉ=çÑ=íÜÉ=íççä=ÜçäÇÉêK=
fãÄ~ä~åÅÉë=ã~ó=Ç~ã~ÖÉ=íÜÉ=éçïÉê=íççäK=
qÜÉ ïçêâ=êÉëìäí=ã~ó=ÄÉ=áãé~áêÉÇK
Operating instructions
klqb
tÜÉå=íÜÉ=éçäáëÜÉê=áë=ëïáíÅÜÉÇ=çÑÑI=íÜÉ=íççä=
ÅçåíáåìÉë=êìååáåÖ=ÄêáÉÑäóK
If using a polishing paste, use the respective
tool for each paste.
On sensitive surfaces (e.g. car paintwork) do
not work aggressively but work at slow speeds
applying low contact pressure.
Sponges can be washed in the washing
machine.
For further information on the manufacturer's
products go to www.flex-tools.com.

Maintenance and care

t^okfkd>
_ÉÑçêÉ=Å~êêóáåÖ=çìí=~åó=ïçêâ=çå=íÜÉ=éçäáëÜÉêI=
~äï~óë=éìää=çìí=íÜÉ=ã~áåë=éäìÖK
Cleaning
t^okfkd>
fÑ=ãÉí~äë=~êÉ=ÖêçìåÇ=çê=Åìí=çîÉê=~=éêçäçåÖÉÇ=
éÉêáçÇI=ÅçåÇìÅíáîÉ=Çìëí=ã~ó=ÄÉÅçãÉ=
ÇÉéçëáíÉÇ=áåëáÇÉ=íÜÉ=ÜçìëáåÖK=
fãé~áêãÉåí=çÑ=íÜÉ=éêçíÉÅíáîÉ=áåëìä~íáçå>
léÉê~íÉ=íÜÉ=éçïÉê=íççä=îá~=~=êÉëáÇì~äJ
ÅìêêÉåíJçéÉê~íÉÇ=ÅáêÅìáíJÄêÉ~âÉê=EíêáééáåÖ=
ÅìêêÉåí=PM ã^FK
Regularly clean the power tool and ventilation
slots. Frequency of cleaning is dependent on
the material and duration of use.
Regularly blow out the housing interior and
motor with dry compressed air.
Polisher L 3403 VRG