Gude MIG 192/6K Originalbetriebsanleitung Seite 13

Device
Welders for manual welding in shielding gas with
automatic wire feed enable jointing of metal parts by fusing
the jointed edges and accessory material. Fusion is
induced by an electric arc generated between the welded
material and metal wire continuously protruding from the
torch end and serving as accessory material for jointing of
parts. Higher welding current allows welding of stronger
sheets. We do not guarantee for damages caused by
neglecting these instructions.
Product Overview
• This gas-shielded Welding Machine MAG series is
designed for ease of welding. It conforms to the safety
standard EN 60974-1 . The device operates with single-
phase input voltage and current at the output. It is mainly
used for the welding of metals such as copper , steel,
low carbon , low alloy steel, stainless steel , etc. .
• This welding machine is mainly characterized by low
cost, high productivity and resistance to corrosion .
There welded slag- free. The unit is very versatile , and
the welding can be done in any position.
• The welding machine is like a step up transformer built
and has a built in wire feed and a feed roller . It is
characterized by ease of use and low failure rate . The
feed rollers can be configured to a range of between 0.5
to 5 kg.
• The voltage can be adjusted gradually. Voltage and
current can be adjusted to the thickness of the metal ..
Multi-speed control of the wire feed .
• Constant voltage
• Equipped with indicator light , heat protection indicators
and cooling fan .
• A device that is easy to carry .
• Accessories for the welding machine are : a MAG
welding gun , a torch , a ground terminal and a welding
hood.
• The device is packaged in a carton.
Welder in MIG 192/6K Shielding Gas
A compact upper-class welder for do-it-yourself works.
With its 6 gear levels, it is also suitable for problematic
welding. With fluently adjustable wire feed and rich
accessories.
Equipment:
Welding shield and pressure control valve with two
pressure indicators. 2 trundles at the back – 2 castor
wheels in the front, including Schuko-CEE 16 A adapter,
protections against thermal overloading and sets of 2-
meter hoses.
Lieferumfang (Abb. 1)
1. Welder with MIG 192/6K shielding gas
2. Set of hoses
3. Grounding terminal
4. Spare nozzles and wire feed pulley
5. Pressure control valve with 2 pressure indicators
6. Power plug
7. Plug with CEE 16 A earthing contact for 230 V
8. Welding shield
Warranty
A warranty period of 12 months applies to commercial use
and 24 months apply to private use and commences on
the day of purchase of the device.
Warranty applies exclusively to failures due to defective
material or workmanship. An original sale slip with
indication of date of sale must be presented in case of
claiming for the warranty rights.
Warranty does not cover unprofessional use such as
device overload, violent use, damage caused by third party
or foreign materials, failure to comply with operations and
assembly manual, and normal wear and tear.
General Safety Instructions
It is necessary to read through the entire Operating
Instructions before first use of the appliance. If there are
any doubts concerning connection and operation of the
appliance, please contact the manufacturer (service
department).
PAY ATTENTION TO THE FOLLOWING
INSTRUCTIONS TO ENSURE HIGH SAFETY LEVEL:
ATTENTION!
Switch-on time
The appliance output is expressed by the
"Einschaltdauer/Switch-on time" (ED%) data on the type
label of the appliance, i.e. ratio between the welding and
cooling time. This factor changes at the same appliance
according to load conditions, i.e. according to the welding
current delivered. It states how long the appliance may
work in the given welding current when loaded and always
relates to the time interval of 10 minutes. E.g. the
appliance works continuously for 6 minutes at welding
current for ED 60%. After this time there is a dead phase
so that inner parts could cool down and protection against
thermal overloading is restarted then.
Use of welders and execution of welding works may
represent a danger both for person handling the appliance
and for others. Therefore the person operating the welder
is in all circumstances obliged not only to read the safety
regulations given here but also know and observe them. It
is necessary to always bear in mind that cautious, well-
instructed operating staff strictly performing their duties is
the best protection from injuries. You should read the
regulations given in the following text and obey them
before connection, preparation, use or transport of the
appliance.
APPLIANCE INSTALLATION
•
Installation and maintenance of the appliance must
take place in accordance with local safety
regulations.
•
Pay attention to the state of wear of cables of
connecting elements and plugs. They need to be
replaced if damaged. Execute regular maintenance
of the equipment. Use cables with sufficient cross-
section only.
• Connect the grounding cable as near to the
workplace as possible.
•
Never use the appliance in a wet environment. Make
sure the workplace, objects situated around and the
welder were dry.
•
PERSONAL PROTECTION AND PROTECTION OF
THIRD PARTIES
Radiation and heat are generated at the welding process.
It is therefore necessary to ensure use of suitable
protective means and take measures for personal
protection and protection of third parties.
•
Never expose yourself or other persons to
electric arc or red hot metal effects without
necessary protection.
Ensure suction of the welding smoke or good
ventilation of the welding workplace.
PREVENTIVE MEASURES AGAINST FIRE AND
EXPLOSION
Hot cinder parts and sparks may cause fire. Fire and
explosion represent other danger. They can be prevented
by observing the following rules:
13