Truma Trumatic S 2200 Gebrauchsanweisung Seite 14

4. Fig. H4: Lead ducts up the
wall with as few bends as pos-
sible. Insert exhaust duct (40)
into the cowl up to the stop
and secure with selftapping
screw (28).
The flue gas pipe (40)
with insulating duct
(41) must be ascending
along its entire length and
securely and permanently
installed using several
clamps (42), since otherwise
a water pocket may form
that will prevent the flue
gas from exiting freely.
Fastening the
heater
Fig. J1: Fasten the heater
through the heater base to
the vehicle floor using the 4
provided selftapping screws
(24). Mount heater casing – if
necessary, with rear panel –
(punch out openings for
ducts on the casing or rear
panel). Tighten bolts (1).
Fig. J2: Use the heat deflec-
tor (25) when the radiation of
heat is to be directed to the
front or when connecting a
fan for warm air distribution.
Warm air
distribution
Fig. K: All Truma fans are
suitable for warm air distribu-
tion (Trumavent or Mulitvent).
The fan can be attached to
the floor or to the wall of the
vehicle, near the heater.
Fig. J2: The connection to
the heater is carried out using
the intake nozzle DT (Part no.
40660-00) with the Trumavent
(for duct diameter 85 mm) or
the intake nozzle DM (Part no.
40670-00) with the Multivent
(for duct diameter 65 mm).
For this connection you require
the installation box EKM or the
rear panel RWS or RWSL with
heat deflector. The Trumavent
fans can also be directly at-
tached to the installation box.
You can use the component
parts of the Trumavent sys-
tem for further expansion of
the warm air system.
Gas connection
The operating pressure
for the gas supply is
30 mbar and must correspond
to the operating pressure of
the appliance (see data plate).
12
The 8 mm diameter gas sup-
ply pipe must be attached to
the connecting piece with a
cutting ring connection.
Carefully counterhold with
another spanner when
tightening!
The gas connection fitting
on the appliance is not to
be made shorter or bent.
Make sure the gas lines are
free of dirt, chips and such
prior to connecting!
Choose a routing for the
ducts which enables the ap-
pliance to be removed again
for service work.
Keep the number of parting
connections in the gas supply
line to an technically feasible
minimum in areas frequented
by people.
The gas system must accord
with the technical and admin-
istrative provisions of the in-
dividual country of use (in Eu-
rope, for example, EN 1949
for motor vehicles).
National regulations and rul-
ings (in Germany, for exam-
ple, the DVGW worksheet
G 607 for motor vehicles)
must be respected.
Function check
After installation, the seal-
ing tightness of the gas
feed line must be tested in
accordance with the pres-
sure drop method. A test
certificate (in Germany, for
example, in accordance with
the DVGW operational data
sheet G 607) is to be issued.
Following this inspection, test
all functions of the appliance
as specified in the operating
instructions.
The operating instructions
and completed guarantee
card are to be given to the
owner of the vehicle.
Warning
information
The installer or vehicle owner
must apply the yellow sticker
with the warning information,
which is enclosed with the ap-
pliance, to a place in the vehi-
cle where it is clearly visible to
all users (e.g. on the wardrobe
door)! Ask Truma to send you
a sticker, if necessary.
Manufacturer's
terms of warranty
1. Case of warranty
The manufacturer grants a
warranty for malfunctions
in the appliance which are
based on material or produc-
tion faults. In addition to this,
the statutory warranty claims
against the seller remain
valid.
A claim under warranty shall
not pertain:
– for parts subject to wear
and in cases of natural
wear and tear,
– as a result of not original
Truma parts being used in
the appliance and as a re-
sult of unsuitable gas pres-
sure regulators being used,
– as a consequence of failure
to respect Truma instruc-
tions for installation and
use,
– as a consequence of
improper handling,
– as a consequence of im-
proper transport packing,
not arranged by Truma.
2. Scope of warranty
The warranty is valid for mal-
functions as stated under
item 1, which occur within
24 months after conclusion of
the purchase agreement be-
tween the seller and the final
consumer. The manufacturers
will make good such defects
by subsequent fulfilment, i.e.
at their discretion either by
repair or replacement. In the
event of manufacturers pro-
viding service under warranty,
the term of the warranty
shall not re commence anew
with regard to the repaired
or replaced parts; rather, the
old warranty period shall con-
tinue to run. More extensive
claims, in particular claims for
compensatory damages by
purchasers or third parties,
shall be excluded. This does
not affect the rules of the
product liability law.
The manufacturer shall bear
the cost of employing the
Truma customer service for
the removal of a malfunction
under warranty – in par-
ticular transportation costs,
travelling expenses, job and
material costs, as long as the
service is carried out in Ger-
many. The warranty does not
cover customer service work
in other countries.
Additional costs based on
complicated removal and
installation conditions of the
appliance (e.g. removal of
furniture or parts of the vehi-
cle body) do not come under
warranty.
3. Raising the case of
warranty
The manufacturer's address
is: Truma Gerätetechnik
GmbH & Co. KG, Wernher-
von-Braun Strasse 12,
85640 Putzbrunn. In Germa-
ny, always notify the Truma
service centre if problems
are encountered; in other
countries the relevant service
partners should be contacted
(see list of addresses). Any
complaints are to be de-
scribed in detail. In addition,
the properly completed guar-
antee certificate is to be pre-
sented, or the factory number
of the unit and the date of
purchase given.
In order for the manufactur-
ers to be able to determine
whether an incident subject
to guarantee has occurred,
the end user must, at his own
risk, bring the device to the
manufacturers or send it to
them. If there is damage to
heaters (heat exchangers),
the gas pressure regulator
must also be sent back to the
factory.
In instances of the device
being sent to the works,
dispatch is to be effected by
freight transport. In cases
under guarantee, the works
shall bear the transport costs
or the costs of delivery and
return. If the damage is
deemed not to be a warranty
case, the manufacturer shall
notify the customer and shall
specify repair costs which
shall not be borne by the
manufacturer; in this case,
the customer shall also bear
the shipping costs.