Scheppach GP600S Originalbetriebsanleitung Seite 23

8.3 Preparing the garden hose (Fig. 1)
1. Unscrew and separate the quick-coupling (7). Slide
the union nut over the garden hose (10) and attach
the quick coupling (7) to the garden hose (10).
2. Now screw it onto the union nut.
3. Unscrew and separate the quick-coupling with the
water-stop (8). Slide the union nut over the other
end of the garden hose (10) and attach the quick
coupling with water-stop (8) to the garden hose (10).
4. Now screw the quick coupling with water-stop (10)
back onto the union nut.
8.4 Installation of a pressure line (Fig. 4)
1. Remove the sealing cap (1a) on the pressure con-
nection (1). Keep the sealing cap (1a) in a safe place!
2. Screw the hose adapter (6) onto the pressure con-
nection (1).
3. Then connect the end of the garden hose with the
quick coupling (7) to the hose adapter (6).
4. During the suction process, the consumers pres-
ent in the pressure line (e.g. syringe, shower, toilet
flush, etc.) must be completely opened so that the
air present in the suction line can escape freely.
8.5 Installation and description of the garden
spray gun (Fig. 1)
1. Connect the garden spray gun (9) to the end of the
garden hose (10) using the quick coupling with wa-
ter-stop (8).
2. The spray pattern of the garden spray gun can be
adjusted by turning the black ring on the outlet side
of the garden spray gun (9). The arrow on the top
of the garden spray gun (9) shows which function
has been selected.
3. Functions of the garden spray gun (9):
• Full: Full, straight jet
• Branch: Three straight, smaller jets
• Flat: One flat jet
• Jet: One narrow, powerful jet
• Shower: Fine jets
9. Operation
m Attention!
Always make sure the product is fully assembled be-
fore commissioning!
m NOTE!
The garden pump must be absolutely leak-proof at the
inlet and outlet. Therefore, regardless of your chosen
connection, use a Teflon or any other sealing tape.
The garden pump runs continuously after being switched
on. As the garden pump does not have a dry-running
cut-off, the pump must be kept under constant obser-
vation during operation to avoid damage due to dry run-
ning. The pump has overheating protection and switch-
es off when the garden pump becomes too warm.
1. Connect the garden pump to the power supply.
2. Actuate the main switch (11). (Fig.1)
Attention: The garden pump starts immediately.
Please ensure that the product is completely as-
sembled.
3. Press the main switch (11) again to switch off the
garden pump. (Fig.1)
10. Uninstallation/Transport
m Attention!
Always unplug the mains plug.
Only use the carrying handle (12) to transport the product.
10.1 Empty the garden pump and domestic wa-
terworks housing prior to transport.
1. Provide a collection bucket with a volume of approx.
2.5 litres (not included) for the water to be drained.
2. Remove the drain screw (4).
3. Allow the water to flow completely into the collec-
tion container from the garden pump.
4. Remove the suction and pressure hose.
5. Remove the connection systems attached to your
garden pump.
6. Then tilt the garden pump so that the residual wa-
ter flows out through the suction and pressure con-
nections (3 and 1).
7. Screw the drain screw (4).
8. Close the suction and pressure connections (3
and 1) using the sealing caps (1a and 3a) to protect
the garden pump from dust and dirt.
11. Maintenance/Cleaning
m Attention!
Only carry out maintenance, cleaning and adjustment
work when the mains plug is pulled out.
We recommend that you clean the product directly af-
ter every use.
m Attention!
Make sure that no water can penetrate the motor. Do
not spray the product with water or clean it under run-
ning water. There is a danger of electric shock and the
product could be damaged.
www.scheppach.com GB | 23