Specifications; Specific Safety Rules - Makita 1923H Betriebshandbuch

ENGLISH
1 Knob
2 Switch trigger
3 Lock button/Lock-off button
4 Bolt
5 Drum
6 Planer blade
7 Drum plate
8 Adjusting plate
9 Inside edge of gauge plate
10 Blade edge
11 Screws
12 Heel
13 Back side of gauge base
14 Gauge plate

SPECIFICATIONS

Model
Planing width ........................................................ 82 mm
Planing depth ....................................................... 3.5 mm
Shiplapping depth ..................................................23mm
–1
No load speed (min ) .......................................... 16,000
Overall length ..................................................... 293 mm
Net weight ...............................................................3.5 kg
Safety class ............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for planing wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to planer safety rules. If you use this tool unsafely or
incorrectly, you can suffer serious personal injury.
1. Wait for the cutter to stop before setting the tool
down. An exposed cutter may engage the sur-
face leading to possible loss of control and seri-
ous injury.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of con-
trol.
3. Rags, cloth, cord, string and the like should
never be left around the work area.
4. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Explanation of general view
15 Gauge base
16 Pan head screw
17 Planer blade locating lugs
18 Heel of adjusting plate
19 Set plate
20 Inside flank of gauge plate
21 Mini planer blade
22 Groove
23 Hex. flange head bolt
24 Vacuum cleaner
25 Screw
26 Nozzle assembly
27 Start
28 End
5.
1923H
6.
7.
8.
9.
/II
10. Make sure the blade is not contacting the work-
11. Wait until the blade attains full speed before cut-
12. Always switch off and wait for the blades to
13. Never stick your finger into the chip chute.
14. Do not leave the tool running. Operate the tool
15. Always change both blades or covers on the
16. Use only Makita blades specified in this manual.
17. Always use the correct dust mask/respirator for
SAVE THESE INSTRUCTIONS.
GEB010-2
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
29 Edge fence
30 V groove
31 Sharpening holder
32 Wing nut
33 Blade (A)
34 Blade (B)
35 Side (C)
36 Side (D)
37 Limit mark
38 Rear cover
39 Screwdriver
40 Carbon brushes
Use only sharp blades. Handle the blades very
carefully.
Be sure the blade installation bolts are securely
tightened before operation.
Hold the tool firmly with both hands.
Keep hands away from rotating parts.
Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced blade.
piece before the switch is turned on.
ting.
come to a complete stop before any adjusting.
Chute may jam when cutting damp wood. Clean
out chips with a stick.
only when hand-held.
drum, otherwise the resulting imbalance will
cause vibration and shorten tool life.
the material and application you are working
with.
5