Specifications; Safety Instructions - Makita 1923B Betriebsanleitung

ENGLISH
1 Bolt
2 Drum
3 Planer blade
4 Drum cover
5 Adjust plate
6 Blade edge
7 Screws
8 Heel
9 Back side of gauge base
10 Inside edge of gauge plate
11 Gauge plate
12 Gauge base
13 Pan head screw
14 Planer blade locating lugs
15 Heel of adjust plate
16 Set plate
17 Inside flank of gauge plate

SPECIFICATIONS

Model
Planing width ...................................................82 mm
Planing depth ....................................................1 mm
Shiplapping depth ........................................... 23mm
–1
No load speed (min ) ................................... 16,000
Overall length ................................................293 mm
Net weight ........................................................ 2.9 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed

Safety instructions.

SAFETY INSTRUCTIONS
Warning! When using electric tools, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury,
including the following. Read all these instruc-
tions before attempting to operate this product
and save these instructions.
For safe operation:
1. Keep work area clean
Cluttered areas and benches invite injuries.
6
Explanation of general view
18 Mini planer blade
19 Hex. flange head bolt
20 Groove
21 Knob
22 Switch trigger
23 Lock button/Lock-off button
24 Start
25 End
26 Blade edge
27 Cutting line
28 Screw
29 Edge fence
30 "V" groove
31 Front base
32 Align the "V" groove with the
edge of the workpiece.
33 Nozzle assembly
2.
1923B/N1923B
3.
4.
5.
6.
7.
8.
9.
10. Connect dust extraction equipment
11. Don't abuse cord
34 Chip cover screw
35 Chip cover
36 Fit pin on nozzle assembly
into this hole.
37 Sharpening holder
38 Wing nut
39 Blade (A)
40 Blade (B)
41 Side (C)
42 Side (D)
43 chip cover
44 Makita vacuum cleaner
45 Limit mark
46 Screwdriver
47 Brush holder cap
Consider work area environment
Don't expose power tools to rain. Don't use
power tools in damp or wet locations. Keep work
area well lit. Don't use power tools in presence of
flammable liquids or gases.
Guard against electric shock
Prevent body contact with grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
Keep children away
Do not let visitors contact tool or extension cord.
All visitors should be kept away from work area.
Store idle tools
When not in use, tools should be stored in dry,
high, or locked-up place, out of the reach of chil-
dren.
Don't force tool
It will do the job better and safer at the rate for
which it was intended.
Use right tool
Don't force small tools or attachments to do the
job of a heavy duty tool. Don't use tools for pur-
poses not intended; for example, don't use circu-
lar saw for cutting tree limbs or logs.
Dress properly
Do not wear loose clothing or jewelry. They can
be caught in moving parts. Rubber gloves and
non-skid footwear are recommended when work-
ing outdoors. Wear protective hair covering to
contain long hair.
Use safety glasses and hearing protection
Also use face or dust mask if cutting operation is
dusty.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used.
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and
sharp edges.