Bosch GCL 2-50 G Professional Originalbetriebsanleitung Seite 16

16 | English
The measuring tool is suitable for indoor and outdoor use.
Product Features
The numbering of the product features shown refers to the il-
lustration of the measuring tool on the graphic page.
(1) Laser beam outlet aperture
(2) Battery indicator
(3) Button for laser operating mode
(4) On/off switch
(5) 1/4" tripod mount
(6) Guide groove
(7) Battery compartment cover locking mechanism
(8) Battery compartment cover
(9) Laser warning label
(10) Serial number
a)
(11) Rotating mount (RM 10)
(12) Guide rail
(13) Fastening slot
(14) Fine adjustment screw of the rotating mount
(15) Magnet
a)
(16) Ceiling clip (DK 10)
a)
(17) Universal holder (BM 1)
a)
(18) Holder (LB 10)
a)
(19) Laser receiver
a)
(20) Laser target plate
a)
(21) Tripod (BT 150)
(22) Telescopic shaft (BT 350)
a)
(23) Laser goggles
a)
(24) Protective bag
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Point and line laser
Article number
A)
Working range
– Standard laser lines
– Laser lines with laser re-
ceiver
– Laser points
B)C)
Levelling accuracy
– Laser lines
– Laser points
Self-levelling range
Levelling time
Operating temperature
Storage temperature
1 609 92A 7LT | (28.04.2022)
a)
The serial number (10) on the type plate is used to clearly identify
your measuring tool.
Assembly
GCL 2-50 G
Inserting/Changing the batteries
3 601 K66 M..
It is recommended that you use alkaline manganese batter-
ies to operate the measuring tool.
15 m
Press the locking mechanism (7) upwards to open the bat-
5–50 m
tery compartment cover (8) and remove the battery com-
partment cover. Insert the batteries.
10 m
When inserting the batteries, ensure that the polarity is cor-
rect according to the illustration on the inside of the battery
compartment.
±0.3 mm/m
The battery indicator (2) always indicates the current status
±0.7 mm/m
of the battery.
±4°
If the batteries are running low, the laser lines will gradually
become dimmer.
< 4 s
–10 °C to +45 °C
–20 °C to +70 °C
Point and line laser
Max. altitude
Relative air humidity max.
Pollution degree according to
IEC 61010-1
Laser class
Laser lines
– Laser type
– C
6
– Divergence
Laser points
– Laser type
– C
6
– Divergence
Compatible laser receiver
Tripod mount
Batteries
Weight according to
EPTA-Procedure 01:2014
Dimensions (length × width × height)
– Without holder
– With rotating mount RM 10
Protection rating
A) The working range may be reduced by unfavourable environ-
mental conditions (e.g. direct sunlight).
B) At 20–25 °C
C) The values stated presuppose normal to favourable environ-
mental conditions (e.g. no vibration, no fog, no smoke, no direct
sunlight). Extreme fluctuations in temperature can cause devi-
ations in accuracy.
D) Only non-conductive deposits occur, whereby occasional tem-
porary conductivity caused by condensation is expected.
GCL 2-50 G
2000 m
90%
D)
2
2
500−540 nm, < 10 mW
10
50 × 10 mrad (full angle)
500–540 nm, < 1 mW
1
0.8 mrad (full angle)
LR 7
1/4"
4 × 1.5 V LR6 (AA)
0.58 kg
126 × 63 × 115 mm
145 × 63 × 180 mm
IP 64
Bosch Power Tools