Work Complete - Scheppach HSM3500 Original Bedienungsanleitung

12.4 Cutting with a non-fixed cutting depth
(Fig. 17)
A non-fixed cutting depth is recommended for easier
cutting of larger cutting depths. In the process, less
stress is placed on the motor (5) and the diamond cut-
ting wheel (14) is preserved.
The workpiece is moved back and forth with the roll
slide (6) under the non-fixed cutting head for this cut.
In the process cutting head (4) is pressed downward
with the right hand.
1. Unscrew the star knob screw (e) on the cutting
head unit (4) and push the cutting arm upwards.
2. Fix the desired cutting depth with the star knob
screw (f).
3. Lower the cutting head unit (4) with the diamond
cutting wheel.
4. Leave the star knob screw (e) unscrewed.
Attention! It should be possible to lower the diamond
cutting wheel (14) approx. 3 mm below the upper edge
of the roll slide (6). The diamond cutting wheel may not
touch the roll slide.
12.5 Cutting with the cutting head – pivot device /
mitre cuts (Fig. 18-20)
Unscrew the cutting head pivot device with the lever
screw (d) and pivot the cutting head (4) 45° to the stop.
Re-tighten the lever.
Attention! Check the stop setting before you begin
cutting. The diamond cutting wheel may not touch the
roll slide.
Perform cutting as described.
12.6 Replacing the diamond cutting wheel
(Fig. 21, 22)
m Attention!
Pull out the mains plug
Caution!
• Danger of cuts on the diamond cutting wheel!
• Wear gloves when replacing the diamond cutting
wheel.
• Check the cutting wheel for direction of rotation,
concentricity and possible damage!
1. Pull out the mains plug.
2. Unscrew the star knob screw (e) on the cutting
head unit (4) and push the cutting arm upwards
completely. Lock the cutting arm with the star knob
(f) on the cutting head unit (4) (Fig. 15).
34 | GB
3. Unscrew and remove the four screws on the
blade's protective cover (1) and remove the pro-
tective cover. Note: It is not necessary to dis-
connect the water hose on the protective cover.
Carefully fold the protective cover down.
4. Hold the cutting shaft in place with the supplied
Allen key and unscrew the clamping nut with the
open-ended spanner (included in the scope of de-
livery). Left-handed thread! Carefully remove the
clamping nut, the pressure flange and the diamond
cutting wheel (14).
5. Before installing the new diamond cutting wheel
(14), clean the cutting shaft and the battery flange
with a rag or brush. Attention! Do not use any
cleaning agents which can corrode the compo-
nents.
Attention! When installing the new diamond cutting
wheel, proceed in the reverse sequence. Make sure
that the direction of rotation is correct! (Insert the
diamond cutting wheel – ARROW DIRECTION – in
the operating side on the flange holder). The arrow
direction on the cutting wheel and the protective cover
must match.
6. Re-mount the saw blade guard (1).
7. Check the concentricity by briefly starting up the
machine and then switching it off again.
Attention!
• Operation of the stone cutting machine is not permit-
ted without the corrective cover!
• When fastening the blade, make sure that the dia-
mond cutting wheel does not „wobble".
• Ensure the firm seating of the water hoses on the
protective cover.

13. Work complete

m Attention!
Pull out the mains plug.
Clean the machine after work is complete.
Drain the water after each use. To do this, remove the
sealing plug (s) from the basin (8).
The basin (8) and the water pump (18) must be regular-
ly cleaned of dirt, otherwise the pump or pipes will be-
come clogged and the cooling of the diamond cutting
wheel (14) will not be ensured.
www.scheppach.com