Package Contents; Description (Fig. A) - DeWalt D25614 Originalanweisung

EnGLIsh
Technical Data).The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.

Package Contents

The package contains:
1 Rotary hammerdrill
1 Side handle
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Date Code Position (Fig. A)
The production date code
by a 2-digit week and is extended by a 2-digit factory code.

Description (Fig. A)


WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Trigger switch
1
Front Barrel (Collar)
2
Mode selector switch
3
Main handle
4
Bit holder
5
Locking sleeve
6
Lock-on switch
7
Intended Use
Your heavy-duty rotary hammerdrill is designed for professional
masonry drilling and chiselling applications.
DO nOt use under wet conditions or in the presence of
flammable liquids or gases.
Your heavy-duty rotary hammerdrill is a professional power tool.
DO nOt let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
24
consists of a 4-digit year followed
11
Electronic speed and
8
impact control dial
Red anti-rotation system
9
indicator LED
Yellow brushwear
10
indicator LED
D WALT tool tag mounting
11
e
holes
Date code
12
2 ; the mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Soft Start Feature
The soft start feature allows the tool to accelerate slowly, thus
preventing the drill bit from walking off the intended hole
position when starting.
The soft start feature also reduces the immediate torque
reaction transmitted to the gearing and the operator if the
hammer is started with the drill bit in an existing hole.
Active Vibration Control (AVC) System
For best vibration control, hold the tool as described in Proper
Hand Position and apply just enough pressure so the damping
device on the main handle is approximately mid stroke.
The active vibration control neutralises rebound vibration from
the hammer mechanism. Lowering hand and arm vibration,
it allows more comfortable use for longer periods of time and
extends the life of the unit.
The hammer only needs enough pressure to engage the active
vibraton control. Applying too much pressure will not make
the tool drill or chip faster and active vibration control will
not engage.
D WALT Tool Tag Ready (Fig. A)
e
Optional accessory
Your hammer comes with mounting holes
for installing a D
install the tag. The D
locating professional power tools, equipment, and machines
using the D WALT Tool Connect™ app. For proper installation of
e
the D WALT Tool Tag refer to the D
e
Lock-On Switch (Fig. A)
chipping mode only
The lock-on switch
applications. To lock the tool on, depress the lock-on switch
while the tool is running. The tool will continue to run after the
switch is released. To unlock and turn off the tool, depress and
release the switch.
Electronic Speed and Impact Control (Fig. A)
The electronic speed and impact control allows the use of
smaller drill bits without the risk of bit breakage, hammerdrilling
into light and brittle materials without shattering and optimal
tool control for precise chiselling.
To set the electronic speed and impact control dial
dial to the desired level. The higher the number, the greater
the speed and impact energy. Dial settings make the tool
extremely flexible and adaptable for many different appli cations.
The required setting depends on the bit size and hardness of
material being drilled.
• When chiselling or drilling in soft, brittle materials or when
minimum break-out is required, set the dial to a low setting;
• When breaking or drilling in harder materials, set the dial to
a high setting.
WALT Tool Tag. You will need a T15 bit tip to
e
WALT Tool Tag is designed for tracking and
e
WALT Tool Tag manual.
e
7 offers increased comfort in extended use
and fasteners
11
8 , turn the