Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Additional Safety Instructions for
Rotary Hammer Drills
•
Use clamps or other practical way to secure and support
the workpiece to a stable platform. Holding the work by
hand or against your body is unstable and may lead to loss
of control.
•
Wear safety goggles or other eye protection. Hammering
operations cause chips to fly. Flying particles can cause
permanent eye damage. Wear a dust mask or respirator
for applications that generate dust. Ear protection may be
required for most applications.
Keep a firm grip on the tool at all times. Do not attempt
•
to operate this tool without holding it with both hands. It
is recommended that the side handle be used at all times.
Operating this tool with one hand will result in loss of control.
Breaking through or encountering hard materials such as
re-bar may be hazardous as well. Tighten the side handle
securely before use.
•
Do not operate this tool for long periods of time.
Vibration caused by hammer action may be harmful to your
hands and arms. Use gloves to provide extra cushion and limit
exposure by taking frequent rest periods.
Do not recondition bits yourself. It should be done by an
•
authorized specialist. Improperly reconditioned bits could
cause injury.
•
Wear gloves when operating tool or changing bits.
Accessible metal parts on the tool and bits may get extremely
hot during operation. Small bits of broken material may
damage bare hands.
Never lay the tool down until the bit has come to a
•
complete stop. Moving bits could cause injury.
•
Do not strike jammed bits with a hammer to dislodge
them. Fragments of metal or material chips could dislodge
and cause injury.
Keep the power cord away from the rotating bit. Do not
•
wrap the cord around any part of your body. An electric cord
wrapped around a spinning bit may cause personal injury and
loss of control.
When working above the floor, make sure that the area
•
below is clear. Falling parts can cause injuries to bystanders.
Reducing of Dust Exposure
Before starting work, check the hazard class of the dust that will
be produced when working.
WARNING: Dust can be harmful to health. Touching or
breathing of some dust created during the work process
by using a power tool and other construction activities
contains chemicals, mineral or particles known to
cause respiratory infections, allergic reactions, cancer,
birth defects or other reproductive harm of the user or
bystanders.
•
Such dusts can be generated, for example, when working
- on hardwoods such as beech or oak, lead based paint, on
concrete, masonry or stones containing quartz.
•
Material containing asbestos may be handled only by
specialists.
•
Observe the relevant regulations in your country for the
materials to be worked on.
•
Use a dust extractor or extraction system with an officially
approved protection class in compliance with the locally
applicable dust protection regulations and suitable for the
material to be worked on.
•
Capture the resulting dust particles directly at the source and
avoid deposits in the surrounding area. Use suitable extraction
accessories for this purpose.
additional measures:
– Make sure that the workplace is well ventilated.
– Wear a respirator appropriate for the type of dust
generated.
Residual Risks
The following risks are inherent to the use of rotary hammers:
•
Injuries caused by touching the rotating parts or hot parts of the tool.
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
•
Impairment of hearing.
•
Risk of squeezing fingers when changing the accessory.
•
Health hazards caused by breathing dust developed when
working in concrete and/or masonry.
•
Risk of personal injury due to flying particles.
•
Risk of burns due to accessories becoming hot
during operation.
•
Risk of personal injury due to prolonged use.
SAVE THESE INSTRUCTIONS
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
i
Your D
WALT tool is double insulated in accordance
e
with EN62841; therefore no earth wire is required.
If the supply cord is damaged, it must be replaced only by
D
WALT or an authorised service organisation.
e
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
•
Safely dispose of the old plug.
•
Connect the brown lead t o the live terminal in the plug.
•
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
EnGLIsh
23
Werbung
Inhaltsverzeichnis
