Circuit Diagram; Preparation Before Use - Hendi H90 Benutzerhandbuch

Main parts of the product
(Fig.1 on page 3)
1. Temperature control knob
2. Temperature light
3. Handle
4. Wire rack mounts
5. Fan
6. Timer knob
7. Timer indicator light
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.

Circuit diagram

(Fig.2 on page 3)
S1. Temperature limiter
PT. Timer
S2. Thermostat
HL1. Power indicator
EL. Chamber light
HL2. Heating indicator
EH1. Heating element 1
EH2. Heating element 2
M1. Motor 1
M2. Motor 2

Preparation before use

• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Operating instructions
(Fig.1 on page 3)
1. Preparation
• Open the glass door using the door handle.
• Insert the trays in a proper position.
• Place the food on the trays and close the door.
• Ensure there is enough space between the food for the heat
to be evenly distributed.
• Connect the power plug to a suitable electrical outlet.
Note: • Do not overload the tray to avoid any damage.
• Check the recipe first for the Timer & Temperature
setting.
ATTENTION! Do not use this trays for storage and processing of
acidic, alkaline or salty food.
2). Start cooking
• Set the 2 controls: Timer knob and the Temperature control
knob to the desired settings. The Timer indicator light , tem-
perature light and internal light of the appliance are all lights
up. The appliance start heating up.
NOTE: The ideal cooking time depends on food type and size,
as well as the selected settings. Some types of food may get
burned, if they are baked, roasted or grilled too long. There-
fore, check the food for doneness in regular intervals through
the glass door.
• When the set time ends, the temperature & timer indicator
goes off.
• To terminate the cooking process manually, just set the Timer
knob to the "0".
• After cooking, set the Temperature control knob to the "0°C".
• Open the glass door using the door handle and remove the
food.
CAUTION! Risk of burns!
• Always open the glass door using the door handle.
• To remove the food, use the tray handle (supplied) and/or oven
mittens (not supplied). Make sure not to touch and damage
the heating elements.
• Keep hands away from steam exiting the appliance.
• After use, disconnect the power plug from the wall outlet.
• Allow the appliance to cool down completely before cleaning
and storing.
3). Timer control
• A cooking time of maximum 120 minutes can be set. For this
purpose, set the Timer knob to the desired time. The cook-
ing time can be increased or decreased at any time during
operation.
NOTE: To set time with higher precision, first turn the Timer
knob over the desired time position a little, then return back
to the desired time position.
• When the set time ends, The Timer indicator light & Tempera-
ture indicator light go off and a sound will be heard.
4). Temperature control
• A cooking temperature of maximum MAX (300°C) can be set.
For this purpose, set the Temperature control knob to the de-
sired temperature.
• Similarly, the cooking temperature can be increased or de-
creased at any time during operation.
NOTE: When the temperature reaches the desired setting, the
and temperature light will go off. If the temperature drops,
the temperature light will light on again. This process will be
repeated automatically.
NOTE: Please note that there is a safety thermal cut out de-
vice for protection located at the lower rear side of the appli-
ance with a protective cap (See ---> RESET the safety cut-out
(Hi-limiter or thermal cut-out) ). This is to prevent the appli-
ance from getting too high and turn off automatically.
GB
7