Transporting The Equipment (Fig. 28); Maintaining The Equipment - Scheppach HS110 Bedienungs- Und Sicherheitshinweise

1. Adjust the parallel stop to the width of workpiece you re-
quire.
2. Use the push block to press the workpiece against the
stop rail and push the workpiece with the push stick (17)
through to the end of the splitter (3).
11.3.3 Making angular cuts (fig. 26)
Angular cuts must always be made using the parallel stop (14).
The parallel stop (14) must always be fitted to the right of the
saw blade. Otherwise, workpieces can become jammed be-
tween the parallel stop and the saw blade during sawing and
ejected at speed.
1. Set the saw blade to the desired angle.
2. Set the parallel stop (14) in accordance with the work-
piece width and height.
3. Carry out the cut in accordance with the workpiece width.
11.4 Making transverse cuts (fig. 27)
1. Push the transverse stop (31) into one of the two grooves
(28a/b) of the saw table and set it to the required angle.
If the sawblade (4) is also to be set at an angle, use the
groove (28a) that prevents your hand and the transverse
stop coming into contact with the saw blade guard.
2. Use the stop rail (30).
3. Press the workpiece firmly against the transverse stop
(31)/stop rail (30).
4. Switch on the saw.
5. Push the transverse stop (31) and the workpiece toward
the saw blade in order to make the cut.
m WARNING: Always hold the guided part of the
workpiece. Never hold the part which is to be cut off.
6. Push the transverse stop (31) forward until the workpiece
is cut all the way through.
7. Switch off the saw again.
8. Do not remove the offcut until the saw blade has stopped
rotating.
11.5 Cutting particle boards
To prevent the cutting edges from cracking when working with
particle boards, you should not set the saw blade (4) more
than 5 mm greater than the thickness of the workpiece.
11.6 After sawing
1. Switch off the circular table saw first and then the suction
system. The saw blade continues to run for a longer time.
2. Do not remove the cut waste on the saw table until the saw
blade has returned to its resting position.
3. Disconnect the circular table saw from the mains by pull-
ing the mains plug out of the power socket.
4. Allow the circular table saw to cool down completely.
11.7 Removing trapped material
m WARNING! Danger of injury!
Improper handling of the circular table saw may result in seri-
ous injury.
• Switch off the circular table saw immediately and disconnect
the mains plug from the power socket if the saw blade is
jammed in the workpiece or other blockages occur.
• Use protective gloves and do not touch the saw blade with
your bare hands.
12 GB/CY
Vibrations can loosen screws and change the position of the
parallel stop.
9.7 Fitting/replacing the saw blade (fig. 13+16)
m WARNING: Pull out the mains plug and wear
protective gloves.
1. Remove the saw blade guard (2) (see 9.4).
2. Remove the table inlay (5) by loosening the two counter-
sunk head screws (25).
3. Insert the Allen key (h) (HX 6) in the screw and hold the
motor shaft in place with the ring spanner (f) (size 22).
ATTENTION: Turn the screw in the direction of rotation
of the saw blade. Remove the loosened screw.
4. Take off the outer flange and pull the old saw blade down
and off the inner flange at an angle.
5. Clean the saw blade flange carefully with a wire brush
before installing the new saw blade.
6. Insert the new saw blade in the reverse sequence and
tighten.
ATTENTION: Observe the running direction, the
cutting angle of the teeth must point in the run-
ning direction, i.e. forwards.
7. Fit and set the table inlay (5) and the saw blade guard (2)
again (see 9.4+13.2).
8. Before working with the saw again, check that the protec-
tive devices are functioning properly.

12. Transporting the equipment (fig. 28)

1. Turn off the power tool before any transport and discon-
nect it from the power supply.
2. Lower the saw blade as far as possible.
3. Wind up the mains cable.
4. Always carry the electric tool with at least one other per-
son. Do not carry the machine by the table extensions, but
only lift it by the housing.
5. Protect the power tool from knocks, bumps and strong vi-
brations, such as during transport in vehicles.
6. Secure the power tool against overturning and sliding.
7. Never use the safety devices for handling or transporting
purposes.

13. Maintaining the equipment

m WARNING! Prior to any adjustment, maintenance or ser-
vice work disconnect the mains power plug!
13.1 General maintenance measures
• Keep protective devices, air vents, suction openings and the
motor housing as free of dust and dirt as possible. Remove
shavings and dust with a vacuum cleaner and a brush. In ad-
dition, blow it out with low-pressure compressed air.
• We recommend that you clean the equipment immediately
after you use it.
• Clean the equipment regularly with a damp cloth and some
soft soap. Do not use cleaning agents or solvents; these may
be aggressive to the plastic parts in the equipment. Ensure
that no water can get into the interior of the equipment.
• In order to extend the service life of the tool, oil the rotary
parts once monthly. Do not oil the motor.