Before Commissioning; Assembly; Saw Blade Guard - Parkside PMTS 210 A1 Originalbetriebsanleitung

Suitable measures include regular maintenance and care of the
power tool and the insertion tools, regular breaks as well as
proper planning of the working process.

8. Before commissioning

• Open the packaging and carefully remove the device.
• Remove the packaging material, as well as the packaging
and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport damage.
• If possible, keep the packaging until the expiry of the war-
ranty period.
m WARNING
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!
• The machine must be securely installed (see 9.9).
• Prior to commissioning, all covers and safety devices must be
mounted correctly.
• The saw blade must be able to run freely.
• In case of previously machined wood, be aware of any for-
eign bodies, such as nails or screws, etc.
• Before pressing the on/off switch, make sure that the saw
blade is correctly fitted, and that moving parts run smoothly.
• Before connecting the machine, make certain that the data
on the type plate matches with the mains power data.
• Only connect the machine to a correctly installed protective
contact socket, with fuse protection of at least 16 A.

9. Assembly

m WARNING:
Remove the mains plug before maintaining, modifying or as-
sembling the circular table saw.
9.1 Fitting the table width extension (fig. 4-6)
1. Loosen the knurled screws (26) (fig. 5).
ATTENTION:
Do not unscrew the knurled screws (26) too far.
2. Feed the guide tubes (23) of the table width extension (22)
into the guide bushings (27) (see fig. 4/5).
NOTE:
To do this, lay the saw on its side.
3. Slide the end pieces (24) into the guide tubes (23) of the
table width extension (22) as shown in fig. 6. Make sure
that one of the two wings of the end pieces (24) can be
clamped by the screw (25) via the screw hole in the guide
tube (23).
4. Fasten the end pieces (24) with the screws (25) as shown
in Fig. 6.
5. Pull the table width extension (22) out completely and fas-
ten it with the knurled screws (26) (fig. 5).
6. Now fold out the support feet (30).
7. Align the table width extension (22) horizontally with the
table saw.
8. Loosen the counternut (29) on the respective support foot
(30) and adjust the height adjustment screw (28) as re-
quired.
9. Then, tighten the counternut (29) again.
If you do not need the table width extension (22), fold the sup-
port feet (30) in. In addition, push the table width extension
(22) all the way in.

9.2 Saw blade guard

m WARNING:
Pull out the mains plug and wear protective gloves.
9.2.1 Fitting/removing the saw blade guard (fig. 7)
1. Undo the wing nut (4a) of the saw blade guard (4). Slide
the coach bolt (4b) in the guide until the groove (A) of the
pin is visible in the opening.
2. Place the saw blade guard (4) onto the riving knife (3)
from above so that the pin sits firmly in the recess of the
riving knife (31).
3. Slide the pin into the guide so that the carriage bolt (4b)
engages in the opening provided for it.
4. Turn the wing nut (4a) clockwise to secure the saw blade
guard in the correct position.
5. Ensure that the saw blade guard (4) can move freely.
6. Disassembly takes place in reverse order.
m WARNING
Danger of injury due to incorrectly mounted saw blade guard
• Before starting sawing, ensure that the saw blade guard (4)
lowers automatically onto the material to be sawn.
9.2.2 Checking the saw blade guard
After fitting, check that the saw blade guard (4) is functioning
properly.
1. Lift the saw blade guard (4) and then release it.
2. The saw blade guard should automatically move back to
its starting position.
9.3 Fitting/removing the table inlay (fig. 8)
m WARNING:
Pull out the mains plug and wear protective gloves.
In the event of wear or damage the table inlay (6) must be
replaced; otherwise there is an increased danger of injury.
1. Move the saw blade into the bottom position (see 10.2).
2. Remove the saw blade guard (4) (see 9.2.1).
3. Remove the screws of the table inlay (32).
4. Remove the table inlay (6).
5. Installation of the table inlay (6) takes place in reverse or-
der.
If the table inlay (6) is damaged, it can be reordered calling the
service number provided in the warranty certificate.
Article number of the table inlay (6):3901309092
GB/IE 9