Storage; Electrical Connection; Disposal And Recycling - Parkside PMTS 210 A1 Originalbetriebsanleitung

Service information
With this product, it is necessary to note that the following parts
are subject to natural or usage-related wear, or that the follow-
ing parts are required as consumables.
Wearing parts*: carbon brushes, table inlay, push stick, saw
blade
* may not be included in the scope of supply!

14. Storage

Store the device and its accessories in a dark, dry and frost-
free place that is inaccessible to children. The optimum storage
temperature is between 5 and 30˚C.
Store the power tool in its original packaging.
Cover the power tool to protect it from dust or moisture.
Store the operating manual with the power tool.

15. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions. The cus-
tomer's mains connection as well as the extension
cable used must also comply with these regula-
tions.
Important information
In the event of overloading, the motor will switch itself off. After
a cool-down period (time varies) the motor can be switched
back on again.
Damaged electrical connection cable
The insulation on electrical connection cables is often dam-
aged.
This may have the following causes:
• Pressure points, where connection cables are passed through
windows or doors.
• Kinks where the connection cable has been improperly fas-
tened or routed.
• Places where the connection cables have been cut due to
being driven over.
• Insulation damage due to being ripped out of the wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be used
and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage regularly.
Ensure that the connection cables are disconnected from elec-
trical power when checking for damage.
Electrical connection cables must comply with the applicable
VDE and DIN provisions. Only use connection cables with des-
ignation "H05VV-F".
The printing of the type designation on the connection cable
is mandatory.
If it is necessary to replace the connection cable, this must
be done by the manufacturer or their representative to avoid
safety hazards.
AC motor
• The mains voltage must be 220-240 V∼.
• Extension cables up to 25 m long must have a cross-section
of 1.5 mm .
2
Connections and repair work on the electrical equipment may
only be carried out by electricians.
Please provide the following information in the event of any
enquiries:
• Type of current for the motor
• Machine data - type plate

16. Disposal and recycling

The device is supplied in packaging to avoid transport dam-
ages. This packaging is raw material and can thus be used
again or can be reintegrated into the raw material cycle.
The device and its accessories are made of different materials,
such as metal and plastic. Take defective components to spe-
cial waste disposal sites. Check with your specialist dealer or
municipal administration!
The packaging is wholly composed of environmen-
tally-friendly materials that can be disposed of at
a local recycling centre.
Contact your local refuse disposal authority for
more details of how to dispose of your worn-out
electrical devices.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must not be dis-
posed of together with domestic waste in compliance
with the Directive (2012/19/EU) pertaining to waste
electrical and electronic equipment (WEEE). This prod-
uct must be handed over at the intended collection point. This
can be done, for example, by returning it when purchasing a
similar product or delivering it to an authorised collection point
for the recycling of old electrical and electronic devices. Im-
proper handling of waste equipment may have negative conse-
quences for the environment and human health due to poten-
tially hazardous substances that are often contained in
electrical and electronic equipment. By properly disposing of
this product, you are also contributing to the effective use of
natural resources. You can obtain information on collection
points for waste equipment from your municipal administration,
public waste disposal authority, an authorised body for the dis-
posal of waste electrical and electronic equipment or your
waste disposal company.
GB/IE 13