Please Read First; Safety; Specified Conditions Of Use; General Safety Instructions - Elektra Beckum BW 750 Betriebsanleitung

Table of Contents
1. Machine overview ..................... 10
2. Please read first!....................... 11
3. Safety ......................................... 11
3.1 Specified conditions of use ......... 11
3.2 General safety instructions ......... 11
3.3 Safety devices ............................ 11
3.4 Symbols on the machine ............ 12
3.5 Symbols used throughout
these instructions........................ 12
4. Special product features.......... 12
5. Transportation and
installation................................. 12
5.1 Machine installation .................... 12
5.2 Machine transport ....................... 12
5.3 Mains connection........................ 12
6. Operation................................... 13
6.1 Cutting ........................................ 13
7. Care and maintenance ............. 13
7.1 Saw blade change ...................... 14
7.2 Saw storage................................ 14
7.3 Maintenance ............................... 14
8. Available accessories ......... 14/51
9. Repairs....................................... 14
10. Environmetal protection .......... 14
11. Trouble shooting ...................... 15
12. Technical specifications .......... 15
12.1 Available saw blades .................. 15

2. Please read first!

•
Read these instructions before initial
operation. Pay special attention to
the safety instructions.
•
Disregard of the instructions voids
the warranty; the equipment manu-
facturer is not liable for any dam-
ages caused by disregard of the
instructions.
•
If you notice transport damage while
unpacking, notify your
immediately. Do not operate the
machine!
•
Dispose of the packing in an envi-
ronmentally friendly manner. Take
to a proper collecting point.
•
Keep these instructions for refer-
ence on any issues you may be
uncertain about.
•
When you hire or sell the machine,
have all documents supplied go with
it.

3. Safety

3.1 Specified conditions of
use
This machine is only intended for cutting
firewood as detailed in these instruc-
tions. Any other use is not as specified.
Unspecified use, modifications to the
machine, or use of parts not tested and
approved by the equipment manufac-
turer may cause unforeseeable damage!
This machine is intended for operation
by one person. Other persons shall keep
a sufficient distance to the machine.
Observe the permissible dimensions of
logs to be cut (see "Technical specifica-
tions").
Never cut several workpieces at the
same time - and also no bundles con-
taining several individual pieces. Risk of
personal injury if individual pieces are
caught by the saw blade uncontrolled.
Never cut logs containing the following:
− ropes
− strings
− cords
− cables
− wires.
Do not overload machine - use it only
within the performance range it was
designed for (see "Technical specifica-
tions").
Use this machine out of doors only.
3.2 General safety instruc-
tions
When using this machine observe the
following safety instructions, to exclude
the risk of personal injury or material
damage.
Please also observe the special safety
instructions in the respective chapters;
where applicable, follow the legal direc-
tives or regulations for the prevention of
accidents pertaining to the use of circu-
lar saws.
A
General hazards!
Be alert. Know what you are doing. Set
out to work with reason. Do not operate
machine while under the influence of
drugs, alcohol or medication.
supplier Keep your work area tidy - a messy
work area invites accidents.
Regularly clear the work area of the cut
logs.
Prevent adverse body positions. Ensure
firm footing and keep your balance at all
times.
Consider environmental effects:
provide proper lighting.
Do not operate machine near inflamma-
ble liquids or gases.
This machine shall only be started and
operated by a person familiar with circu-
lar saws and who is at all times aware of
the dangers associated with the use of
such machine.
Keep bystanders, particularly children,
out of the danger zone. Persons under
18 years of age shall use this machine
only in the course of their vocational
training, under the supervision of an
ENGLISH
instructor.
Do not permit other persons to touch the
machine or power cable while it is run-
ning.
B
Danger! Risk of electric shock!
To ensure the machine remains weath-
erproof, before any use check to see
that the switch, power cable or plug are
not damaged (no cracks, etc.)
Do not use the power cable for any pur-
pose it is not intended for.
A
Risk of personal injury and
crushing by moving parts!
Do not operate the machine without
installed guards.
Keep sufficient distance to driven com-
ponents when operating the machine.
Ensure the machine is disconnected
from power supply before servicing.
Ensure that when switching on (e.g. after
servicing) no tools or loose parts are left
on or in the machine.
Turn power off if the machine is not
used.
A
Hazard generated by modifica-
tion of the machine or use of parts
not tested and approved by the equip-
ment manufacturer!
Use only parts approved by the equip-
ment manufacturer. This applies particu-
larly to:
− saw blades (see "Technical specifi-
cations" for stock numbers);
− safety devices (see "Spare parts list"
for stock numbers).
Do not change any parts.
A
Hazard generated by machine
defects!
Keep machine and accessories in good
repair. Observe the
instructions.
Before any use check machine for possi-
ble damage: before operating
machine all safety devices, protective
guards or slightly damaged parts need to
be checked for proper function as speci-
fied. Check to see that all moving parts
work properly and do not jam. All parts
must be correctly installed and meet all
conditions necessary for the proper
operation of the machine.
Damaged protection devices or parts
must be repaired or replaced by a quali-
fied specialist. Have damaged switches
replaced by a service centre. Do not use
this machine if the switch can not be
turned ON or OFF.
Keep handles free of oil, grease and
resin.
3.3

Safety devices

Motor protection
The electronic motor protection stops
the motor by overcurrent detection,
maintenance
the
11