Servicing The Wheels (Illustration S ); 16 Troubleshooting - Sabo 40-EL SPIRIT Betriebsanleitung

In addition, a wrongly assembled cutting blade coupling can allow the cutter bar to become loose, which can lead to
serious injuries.
Pos: 13.22 /Innenteil/Pflege und Wartung des Mähers/Auswechseln des Messerbalkens Text Elektro+Benzin neu @ 21\mod_1351068532063_1521.doc @ 160267 @ @ 1
– Only use original blades for replacement purposes.
– Blades must be indelibly marked with name and/or trademark of the manufacturer or supplier and with the parts number.
Pos: 13.23 /Innenteil/Pflege und Wartung des Mähers/1.1 Wartung der Räder (Abbildung S) @ 0\mod_1125651856935_1521.doc @ 1819 @ 2 @ 1

Servicing the wheels (Illustration S )

Pos: 13.24 /Innenteil/Pflege und Wartung des Mähers/Wartung der Räder Text Elektro, 52er,47er,43er,40er @ 21\mod_1351675692916_1521.doc @ 161964 @ @ 1
Oil the bearings of the wheels once a year or every 50 operating hours.
– Remove wheel covers.
– Loosen the hexagon head nuts using a socket wrench and remove the wheels.
– After oiling the bearings, push the wheels on and tighten them again so that they still turn easily but without any play.
Pos: 14.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.doc @ 2070 @ @ 1
Pos: 14.2 /Innenteil/Störungsursachen und deren Beseitigung/1 STÖRUNGSURSACHEN UND DEREN BESEITIGUNG @ 0\mod_1115373523343_1521.doc @ 1904 @ 1 @ 1

16 TROUBLESHOOTING

Pos: 14.3.1 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/1 Tabellenkopf @ 0\mod_1115374760156_1521.doc @ 1884 @ @ 1
Fault
Pos: 14.3.2 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Motor läuft nicht an Elektro @ 13\mod_1280992241502_1521.doc @ 110776 @ @ 1
If the motor does not start 5
seconds after the unit is started
Pos: 14.3.3 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Starke Erschütterungen (Vibrieren) @ 0\mod_1115377318234_1521.doc @ 1900 @ @ 1
Extreme vibration
GB
Pos: 14.3.4 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Schnitt unsauber, Rasen wird gelb, Elektro @ 0\mod_1125904144842_1521.doc @ 1899 @ @ 1
Unclean cut, lawn is yellow
Pos: 14.3.5 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Auswurf verstopft, Elektro @ 3\mod_1157713644050_1521.doc @ 19339 @ @ 1
Ejection blocked
Pos: 14.4 /Innenteil/Störungsursachen und deren Beseitigung/Störungsursachen und deren Beseitigung Text Elektro @ 0\mod_1125668481258_1521.doc @ 1906 @ @ 1
Repairs to electrical machines must always be performed only by qualified electricians. Please do not repair them yourself.
In the case of faults and defects which have not been listed here, please contact the nearest authorized dealer. This applies
in particular to appliances with electrical motors, as when these are repaired they must always undergo an insulation
protection test.
Your authorized dealer will also help you if you do not wish to perform any of the maintenance work described here yourself.
=== Ende der Liste für Textmarke Inhalt ===
Possible cause
No power supply.
Power cable damaged.
Cutting height has been set too low
(grass is too high and blocks the
starting of the motor).
Too much grass waste in the
housing.
Blade blunt.
Cutting height too low.
Mowing too fast.
Insufficient overlapping of cuts when
mowing.
Lawn becomes matted.
Cutting height too low for grass that
is too high.
Pushing mower too fast.
Grass not dry.
14
Remedy
Connect the plug C2 .
Check the fuse.
Get it checked by an authorised workshop.
Set a higher cutting height I .
Machine tilts when starting it.
Clean the cutting chamber of grass, ensure
that the gap between fan and housing is
kept clean (pull the plug first!).
Get it checked by an authorised workshop.
Have it checked by an authorized dealer
Have it sharpened and balanced by an
authorized dealer Q .
Adjust to higher cutting height I .
Adjust mowing speed.
Tall grass conditions may dictate that more
overlapping of cuts is required.
A lawn scarifier can remedy the problem
considerably
Adjust to higher cutting height I .
Adjust mowing speed.
Let grass dry.