Assembly And Adjustments - DeWalt XR DCH172 Bersetzung Der Originalanweisungen

EnGLIsh
Markings on Tool
The following pictograms are shown on the tool:
a
Read instruction manual before use.
g
Wear ear protection.
f
Wear eye protection
n
Visible radiation. Do not stare into light.
Date Code Position (Fig. B)
The date code 13 , which also includes the year of manufacture,
is printed into the housing.
Example:
2021 XX XX
Year and Week of Manufacture
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Side handle
1
Depth rod
2
Trigger switch
3
Forward/reverse control button (Lock‑off button)
4
Mode selector
5
6 Main handle
Worklight
7
Battery pack
8
Battery release button
9
Active Vibration Control
10
Utility hook
11
Lanyard attachment point
12
Intended Use
This heavy‑duty cordless rotary hammer is designed for
professional concrete, wood and metal drilling applications.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
This heavy‑duty cordless rotary hammer is a professional
power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
36

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack with the rails inside the tool's
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which consists
e
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 14 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level of
charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Electronic Overload Protection
If the drill bit becomes jammed, the power to the drill spindle
will be interrupted by the activation of the electronic overload
protection. To reactivate the power to the drive spindle, the
tool's trigger should be released and then depressed. Due to the
resulting forces, always hold the tool with both hands and take
a firm stance.
Active Vibration Control (Fig. A)
For best vibration control, hold the tool with one hand on the
main handle 6 and the other hand on the side handle
just enough pressure so the Active Vibration Control
rear handle are halfway depressed. The hammer only needs
enough pressure to engage the internal active vibration control.
Applying too much pressure will not make the tool drill faster
and active vibration control will not engage.
WALT battery packs and chargers.
e
8 is fully charged.
9 and firmly pull the
1
10 in the
. Apply