Technical Data; Assembly - Scheppach DP16SL Original Bedienungsanleitung

7. Technical data

Length x width x height
in mm
Table size in mm
Table pivot range in °
Table turning range in °
Gap between the chuck
and the table in mm
Gap between the chuck
and the floor plate in mm
Column ø in mm
Chuck adapter
Drill chucking range in mm
Maximum drilling depth
in mm
Speed stages in rpm
Engine
Motor output in W
Operating mode
Cable length in mm
Weight kg
Technical changes reserved!
Noise
The noise levels have been determined in accord-
ance with EN 3746.
Sound pressure level Idle L
Sound pressure level L
pA
Uncertainty K
pA
Sound power level Idle L
WA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection.
Excessive noise can result in a loss of hearing. Total
vibration emission values (vector sum of three direc-
tions) determined per EN 61029.

8. Assembly

Warning:
For you own safety, never insert the plug into the
socket until you have completed all assembly steps
and you have read and understood the safety and
work instructions.
8.1 Column (5) and base plate (1) (Fig. 2)
1. Set the base plate foot (1) down on the floor or
the workbench.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
235 x 482 x 732
194 x 165
- 45 / 0 / 45
360
305
405
48
B16
3 - 16
50
510 - 800 - 1300 -
1800 - 2430
230V / 50Hz
550
S2 10min
1830
23
70,7 dB (A)
pA
73,9 dB (A)
3 dB
82,8 dB (A)
86 dB (A)
3 dB
2. Place the column (5) on the base plate (1) so that
the holes on the column (5) align with the holes
on the base plate (1).
3. Screw the three screws (6) to fasten the column
(5) into the base plate (1) and tighten them using
an open-ended spanner (size 13).
8.1 Removing the toothed rack (4) (Fig. 3)
In order to be able to install your drill, you must first
remove the toothed rack (4).
1. Use an Allen key (size 3) to remove the ring (7)
and pull this off the column (5).
2. Now pull the toothed rack (4) out.
8.2 Installing the drilling table holder (2) (Fig. 4)
1. Insert the toothed rack (4) into the groove on the
drilling table holder (2).
2. Align the toothed rack (4) centrally in relation to
the drilling table holder (2).
3. When bringing the toothed rack (4) together
within the groove, ensure that the tooth meshing
between the toothed rack (4) and the drilling ta-
ble holder (2) is correct.
4. Now place the drilling table holder (2) with the
toothed rack (4) on the column (5) and guide the
toothed rack (4) into the bottom rack guide on
the column foot.
5. Use the ring (7) to secure the toothed rack (4).
Ensure that the toothed rack guide on the ring
(7) is pointing downwards. Tighten the integrat-
ed grub screw to affix the ring (7).
6. Connect the adjustment handle for height ad-
justment (3) to the drilling table holder's shaft (2)
and use a grub screw to secure it.
8.3 Installing the machine head (8) and column
(5) (Fig. 5)
1. Place the machine head (8) on the column (5).
2. Align the drill's spindle (33) with the drilling ta-
ble (18) and the base plate (1), and tighten the 2
grub screws located on the side of the machine
head (8). (Size 4 Allen key)
8.4 Installing the chuck guard holder (16) (Fig. 6)
1. Place the chuck guard (16) on the spindle tube
and tighten the slotted screw (17).
8.5 Installing the handles (9) on the vertical
drive's crank (Fig. 7)
1. Screw the handles (9) tight in the spindle hub's
thread.
GB | 27