Technical Data - Scheppach DH1300PLUS Original Bedienungsanleitung

• Pull the plug out of the socket and/or remove
the battery before making any adjustments to
the appliance, changing accessories or put the
appliance down. This safety measure prevents
starting the electric tool unintentionally.
• Keep unused electric tools out of the reach of
children. Do not allow people who are not fa-
miliar with the appliance or who have not read
these instructions to use the appliance. Electric
tools are dangerous if they are used by inexperi-
enced people.
• Clean your electric tool carefully. Check
whether moving parts are functioning proper-
ly and not jamming, whether parts are broken
or damaged enough that the functioning of this
electric tool is affected. Have damaged parts
repaired before using the appliance. Many ac-
cidents are caused by badly maintained electric
tools.
• Keep your cutting tools sharp and clean. Care-
fully maintained cutting tools with sharp cutting
edges will jam less and are easier to control.
• Make sure to use electric tools, accessories,
attachments, etc. in accordance with these in-
structions. Take the conditions in your work
area and the job in hand into account. Using
electric tools for any purpose other than the one
for which they are intended can lead to danger-
ous situations.
Service
• Have your electric tool repaired only by trained
personnel using only genuine spare parts. This
will ensure that your electric tool remains safe to
use.
Safety Information for hammer
• Wear ear protection. The impact of noise can
cause damage to hearing.
• Use the additional handles supplied with the
tool. Losing control of the tool can cause injuries.
• Hold the equipment by the insulated handles
when carrying out work during which the plug-
in tool could strike concealed power cables or
its own mains lead. Contact with a live cable can
also make the metal parts of the equipment live
and will cause an electric shock.
Do not lose these safety instructions
Residual risks
Even if you use this electric power tool in ac-
cordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
• Lung damage if no suitable protective dust mask
is used.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Damage to hearing if no suitable ear protection is
used.
• Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or is
not properly guided and maintained.

5. Technical data

Mains voltage
Power input
Idling speed
Blow rate
Drilling capacity in con-
crete/stone (max.)
Protection class
Weight
Danger!
Sound and vibration
Sound and vibration values were measured in ac-
cordance with EN 60745.
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 60745.
Main handle
Hammer drilling in Concrete:
a = 13.59 m/s , K = 1.5 m/s
2
h(HD)
Additional handle
Hammer drilling in Concrete:
a = 11.265 m/s , K = 1.5 m/s
2
h(HD)
Main handle
Chiselling: a = 14.3 m/s
h(CHeq)
Additional handle
Chiselling: a = 14.51 m/s
h(CHeq)
The specified vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep-
tional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
220-240 V~ 50 Hz
1250 W
850 min
-1
4500 bpm
30 mm
II
4.9 kg
90.9 dB(A)
3 dB(A)
101.9 dB(A)
3 dB(A)
2
2
, K = 1.5 m/s
2 2
, K = 1.5 m/s
2 2
GB | 17