3M Peltor WS ProTac XPI Headset Bedienungsanleitung Seite 13

EN
two-way radio supports 3M™ PELTOR™ Push-To-Talk protocol.
If you have any questions, please contact your local distributor.
NOTE: When a third Bluetooth
®
one of the previously paired devices is removed from the
headset. If one of the devices is connected, the unconnected
device is removed. Otherwise, the first paired device is removed.
2:11 Reconnecting Bluetooth
When the headset is powered on, it tries to reconnect to all
paired devices during 5 minutes. A voice message will confirm
the connection, "connected".
NOTE: If the link is lost, a voice message will confirm with
"disconnected".
2:12 Bluetooth function
®
Bluetooth is the name of a technical standard for short-
®
range wireless transmission, with a working range of
approximately 10 metres. This headset can be used with
other Bluetooth -enabled units that support any of the
®
profiles: headset (HSP), hands-free (HFP), or streaming
audio (A2DP).
• If the message "no paired devices" is heard, no Bluetooth
device is linked to the headset.
• If the message "connecting Bluetooth
heard, a Bluetooth enabled device is linked to the
®
headset and connected.
• If the message "connecting Bluetooth
is heard, a Bluetooth device is linked to the headset, but
®
not connected.
2:13 Answer a phone call (fig. 7)
When the headset is connected to a phone via Bluetooth
wireless technology and there is an incoming call, answer
by pressing briefly on the Bluetooth
cup.
2:14 Reject a call (fig. 7)
Press and hold the Bluetooth
a phone call.
2:15 Adjust Bluetooth volume (fig. 3)
®
Press the [+] or [–] buttons to adjust the volume on an active
paired Bluetooth device.
®
2:16 Toggle between phone and headset (fig. 7)
When a call is active, it is possible to transfer the audio to
the phone instead of the headset, by pressing the
Bluetooth button for 2 seconds. To return the call to the
®
headset, press the Bluetooth
more.
device is successfully paired,
devices
®
, connected" is
®
, connection failed"
®
®
button on the right
®
button for 2 seconds to reject
®
button for 2 seconds once
®
2:17 Finish a phone call (fig. 7)
To finish an ongoing phone call, press the Bluetooth
button briefly.
2:18 Redial (fig. 7)
The last dialed number on a phone connected via
Bluetooth can be redialed. Press and hold the Bluetooth
®
button for 2 seconds.
2:19 Voice dial (fig. 7)
To activate voice control of the last paired device, short
press the Bluetooth button.
®
3. CONFIGURING YOUR HEADSET (fig. 8)
Settings are changed in the menu. Press and hold the [+]
and [–] buttons for approximately 2 seconds to access the
menu. To step through the menu, press the On/Off/Mode
button briefly. The menu steps are listed below. At each
menu step the [+] and [–] buttons are used to change the
setting and step through the available settings. A voice
message confirms each menu step. After ten seconds of
inactivity, the menu returns to volume mode.
®
3:1 Bluetooth pairing (fig. 6)
®
When the voice message says "Bluetooth
press (1 s) the [+] button to start pairing. Short press (1 s)
the Bluetooth button to stop pairing. A voice message will
®
confirm, "Bluetooth pairing on". Search and select "WS
®
ProTac XPI" on your Bluetooth
will confirm when pairing is complete, "pairing complete"
and "connected". Short press (1 s) the [–] button to stop the
pairing. A voice message will confirm, "pairing failed".
3:2 VOX (voice operated transmission)
VOX enables automatic transmission when the sound level
at the microphone is above the VOX level. This allows radio
transmission without pressing the Bluetooth
are two settings: off mode (default) and on mode for
activating voice operated transmission.
3:3 Battery type
Battery type adjusts the indication of low battery warning
for different types of battery. It is adjustable for two types
of batteries: rechargeable and alkaline.
3:4 Reset (reset to factory default) (fig. 9)
To confirm a reset to factory default, hold the [+] button for
two seconds.
5
®
®
pairing", short
®
device. A voice message
®
button. There
®