Switching Signal Channels, Ssc - Balluff BIP LD2-T017-01-EP Serie Betriebsanleitung

BIP LD2-T017-01-EP _ _ / EP _ _ -S4
Inductive Positioning System
6
IO-Link interface (continued)
6.8

Switching Signal Channels, SSC

With the BIP sensor you can program four independent
switching states (Switching Signal Channels, SSCs).
Each switching signal is configured using profile-specific
parameters (see Tab. 6-10). Configuring the switching
channel begins by setting the channel using Index 0x003A.
Index Parameters
0x003A Teach-In Channel
Setting
0x003B Teach-In Status
0x003C Set Point value
(SSC1)
0x003D Switching Signal
configuration SSC1
0x003E Set Point value
(SSC2)
0x003F Switching Signal
configuration SSC2
0x4000 Set Point value
(SSC3)
0x4001 Switching Signal
configuration SSC3
0x4002 Set Point value
(SSC4)
0x4003 Switching Signal
configuration SSC4
Tab. 6-10: Profile-specific parameters
www.balluff.com
Subindex Parame- Data format
ters
0x00
0x00
0x01 Setpoint1
0x02 Setpoint2
0x01 logic
0x02 mode
0x03 hysteresis
0x01 Setpoint1
0x02 Setpoint2
0x01 logic
0x02 mode
0x03 hysteresis
0x01 Setpoint1
0x02 Setpoint2
0x01 logic
0x02 mode
0x03 hysteresis
0x01 Setpoint1
0x02 Setpoint2
0x01 logic
0x02 mode
0x03 hysteresis
Based on the Smart Sensor profile the Parameter
Switching Signal configuration can be used to set the
behavior of the switching points:
– Single-point mode, (Fig. 6-2): Value: 1
– Two-point mode, (Fig. 6-3): Value: 3
– Windowed mode, (Fig. 6-4): Value: 2
Switching signals can only be taught as long as
the position value is valid.
Access Data
UINT8 R/W 0x01: SSC1
0x02: SSC2
0x03: SSC3
0x04: SSC4
UINT8 R
INT16 R/W –32000...+32000
INT16 R/W –32000...+32000
UINT8 R/W 0x00 : normal mode
0x01: inverted mode
UINT8 R/W 0x01: Single point
0x02: Window mode
0x03 Two Point mode
INT16 R/W 50...16900 μm
INT16 R/W –32000...+32000
INT16 R/W –32000...+32000
UINT8 R/W 0x00 : normal mode
0x01: inverted mode
UINT8 R/W 0x01: Single point
0x02: Window mode
0x03 Two Point mode
INT16 R/W 50...16900 μm
INT16 R/W –32000...+32000
INT16 R/W –32000...+32000
UINT8 R/W 0x00 : normal mode
0x01: inverted mode
UINT8 R/W 0x01: Single point
0x02: Window mode
0x03 Two Point mode
INT16 R/W 50...16900 μm
INT16 R/W –32000...+32000
INT16 R/W –32000...+32000
UINT8 R/W 0x00 : normal mode
0x01: inverted mode
UINT8 R/W 0x01: Single point
0x02: Window mode
0x03 Two Point mode
INT16 R/W 50...16900 μm
english 17