AEG POWERTOOLS SB2E 850 R Originalbetriebsanleitung Seite 17

WARNING! Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
DRILL SAFETY WARNINGS
Wear ear protectors when impact drilling. Exposure to noise
can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory con-
tacting a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
SCREWDRIVER SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, when
GB
performing an operation where the fastener may contact
hidden wiring or its own cord. Fasteners contacting a "live"
wire may make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Additional Safety and Working Instructions
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is re-
commended, such as dust mask, protective gloves, sturdy non-slip
footwear, helmet and ear defenders.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
Do not machine any materials that present a danger to health (e.g.
asbestos).
When working in walls ceiling, or oor, take care to avoid electric
cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpi-
eces can cause severe injury and damage.
Switch the device o immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled,
as doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
Possible causes can be:
• it is tilted in the workpiece to be machined
• breakage of the material to be used
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is
running.
Always disconnect the plug from the socket before carrying out any
work on the machine.
English
English
14
SPECIFIED CONDITIONS OF USE
The electronic percussion drill/screwdriver can be universally used
for drilling, percussion drilling, screwdriving and cutting screw
threads.
EC DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under "Technical Data" ful lls all the relevant provisions of the
directives:
2011/65/EU (RoHS)
2014/30/EU
2006/42/EC
and the following harmonized standards have been used.
EN 60745-1:2009 + A11:2010
EN 60745-2-1:2010
EN 60745-2-2:2010
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 50581:2012
Winnenden, 2017-09-25
Alexander Krug / Managing Director
Authorized to compile the technical le
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
MAINS CONNECTION
Appliances used at many di erent locations including wet room
and open air must be connected via a residual current device (FI,
RCD, PRCD) of 30mA or less.
Connect only to single-phase AC system voltage as indicated on
the rating plate. It is also possible to connect to sockets without an
earthing contact as the design conforms to safety class II.
Only plug-in when machine is switched o .
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
If the machine is mainly used for percussion drilling, regularly
remove collected dust from the chuck. To remove the dust hold the
machine with the chuck facing down vertically, and completely
open and close the chuck. The collected dust will fall from the
chuck. It is recommended to regularly use cleaner for the clamping
jaws and the clamping jaw borings.
If the supply cord of this appliance is damaged, it must only be
replaced by a repair shop appointed by the manufacturer, to avoid
hazardous situations.
Use only AEG accessories and spare parts. Should components
need to be replaced which have not been described, please contact
one of our AEG service agents (see our list of guarantee/service
addresses).
Автотовари «130»