Specifications - Monacor LEDS-5SET/RGB Bedienungsanleitung

4.2 Selecting the control programme
For direct selection of the 29 programmes, press
the coloured buttons (14) [repeatedly].
Button
R constant red
G constant green
B constant blue
Y constant yellow
C constant cyan
P constant purple
G R B constant white
To run through the control programmes succes-
sively, press the button AUTO (10). The pro-
grammes with the LEDs constantly lighting are
skipped.
To switch between different programmes, the
buttons MODE (9) can also be actuated. To switch
from the programme constant lighting in red to the
function for running through all programmes, press
the button MODE .
8 Button ON for switching on
9 Buttons MODE for selection of a control pro-
gramme
10 Button AUTO: for running through the control
programmes successively
11 Buttons SPEED for the speed (9 levels)
12 Button OFF for switching off
13 Buttons BRIGHT for the brightness (9 levels) for
the programmes change of colour, flashing and
constant colour
14 Buttons for direct selection of the 29 control pro-
grammes (see chapter 4.2)
15 Button PAUSE to interrupt / continue the pro-
gramme run
16 Button RESET to reset the control to the initial
state (keep button pressed longer)
®
Copyright
LEDS-5SET/RGB
Press the button repeatedly to switch between the programmes of a line
red becoming
brighter and darker
green becoming
brighter and darker
blue becoming
brighter and darker
yellow becoming
brighter and darker
cyan becoming
brighter and darker
purple becoming
brighter and darker
gradual transition
between all colours
4.3 Brightness, speed, pause, reset, on / off
1) To adjust the LED brightness, press the buttons
BRIGHT (13). 9 levels are available. However,
the brightness can only be adjusted for the pro-
grammes change of colour, flashing and con-
stant colour. For the remaining programmes the
brightness is exclusively defined by the pro-
gramme.
2) Adjust the running speed with the buttons
SPEED (11). Nine speed levels are available.
8
9
10
© by MONACOR INTERNATIONAL GmbH & Co. KG, Bremen, Germany. All rights reserved.
Order No. 38.5420
flashing in red
flashing in green
flashing in blue
flashing in yellow
flashing in cyan
flashing in purple
change of colour
red – blue – green
11
12
O N O F F
13
MODE MODE SPEED SPEED BRIGHT BRIGHT
R G B
14
Y C P
R R
G G
B B
15
16
AUTO PAUSE RESET
LEDS-5SET/RGB
gradual transition
green – red
gradual transition
blue – green
gradual transition
red – blue
change of colour
red – green – yellow – blue –
purple – cyan – white
3) The button PAUSE (15) allows to stop and
restart the run of the control programme.
4) By keeping the button RESET (16) pressed for a
few seconds, the control is reset to the initial
state. Then the brightness of the LEDs is set to
the maximum value and the running speed to the
medium value and the unit is switched to the
function for running through all programmes.
5) To switch off the LEDs, press the button OFF
(12); to switch them on again, press the button
ON (8).

5 Specifications

Type and number of LEDs: . . 150 RGB LEDs
Beam angle: . . . . . . . . . . . . . 120°
Power supply: . . . . . . . . . . . . 12 V via supplied
Ambient temperature: . . . . . . 0 – 40 °C
Dimensions
LED strip: . . . . . . . . . . . . . 10 × 3 × 5000 mm
controller: . . . . . . . . . . . . . 103 × 19 × 37 mm
remote control: . . . . . . . . . 40 × 7.5 × 86 mm
Power supply unit: . . . . . . 120 × 33 × 52 mm
Subject to technical modification.
A-1218.99.01.03.2011
change of colour
green – red
change of colour
blue – green
change of colour
red – blue
white becoming
brighter and darker
PSU connected to
230 V~ / 50 Hz