Grundfos Control MPC-Serie Installationsanleitung Seite 418

Date and time 4.5.3 Temperature
Password 4.5.4
Ethernet 4.5.5
GENIbus number 4.5.6
Software status 4.5.9
418
Alternative setpoints 2-7
External setpoint influence
Input value to be influenced by
Setting of influence function 4.1.3.2
Min. time between start/stop
Max. number of starts/hour
Forced pump changeover
Pump start and stop speed
Compensation for pump start-up time
Stop parameters
Function, DI1 (CU 352) - DI3, [10, 12, 14]
Function, DI1 (IO 351-41) - DI9, [10-46]
Function, DI1 (IO 351-42) - DI9, [10-46]
Setting, AI1 (CU 352), [51] - AI3, [51, 54, 57]
Function, AI1 (CU 352) - AI3 [51, 54, 57]
Setting, AI1 (IO 351-41), [57] - AI2 [57, 60]
Function, AI1 (IO 351-41) - AI2 [57, 60]
Setting, AI1 (IO 351-42), [57] - AI2 [57, 60]
Function, AI1 (IO 351-42) - A2 [57, 60]
DO1 (CU 352), [71] is signalling - DO2 [71, 74]
DO1 (IO 351-41), [77] is signalling - DO7 [77-88]
DO1 (IO 351-42), [77] is signalling - DO7 [77-88]
AO1 (IO 351-41) [18] - AO3 [18, 22, 26]
AO1 (IO 351-42) [18] - AO3 [18, 22, 26]
[12 ، 10] DI2 - [10] ,(IO 351-41)
[12 ، 10] DI2 - [10] ,(IO 351-42)
Min., max. and user-defined duty
Min. duty
Max. duty
Set user-defined duty
Flow estimation
Pressure/level switch
Measurement, inlet pressure
Measurement, tank level
Pumps outside duty range
Change language to the service language (English)
Pressure
Differential pressure
4.5.2.8
Power 4.5.2.9 Flow rate
Energy 4.5.2.10 Volume
Specific energy
Primary controller
PI controller 4.1.1
Alternative setpoints 4.1.2
4.1.2.1
4.1.3
4.1.3.1
Primary sensor 4.1.4
Secondary sensor 4.1.5
Clock program 4.1.6
Proportional pressure 4.1.7
S-system configuration 4.1.8
Setpoint ramp 4.1.9
Pump cascade control
4.2.1
Standby pumps 4.2.3
4.2.4
Pump test run 4.2.5
Pump stop attempt 4.2.7
4.2.8
Min. performance 4.2.9
4.2.10
Secondary functions
Stop function 4.3.1
4.3.1.1
Pilot pump 4.3.2
Soft pressure build-up 4.3.3
Emergency run 4.3.5
Digital inputs 4.3.7
Analog inputs 4.3.8
Digital outputs 4.3.9
Analog outputs 4.3.10
Counter inputs 4.3.11
DI1 ، ‫ﻋ ﺩﺍﺩ ﺍﻟﺻ ﻭﺕ‬
DI1 ، ‫ﻋ ﺩﺍﺩ ﺍﻟﺻ ﻭﺕ‬
4.3.14
4.3.14.1
4.3.14.2
4.3.14.3
Pilot pump curve data 4.3.18
Pump curve data 4.3.19
4.3.23
Control source 4.3.20
Fixed inlet pressure 4.3.22
Flow estimation 4.3.23
Reduced operation 4.3.24
Multisensor settings 4.3.25
Monitoring functions
Dry-running protection 4.4.1
4.4.1.1
4.4.1.2
4.4.1.3
Min. pressure 4.4.2
Max. pressure 4.4.3
External fault 4.4.4
Limit 1 exceeded 4.4.5
Limit 2 exceeded 4.4.6
4.4.7
Pressure relief 4.4.8
Log values 4.4.9
Fault, primary sensor 4.4.10
Non-return valve 4.4.11
Functions, CU 352
Run wizard again
Display language 4.5.1
Units 4.5.2
4.5.2.1
4.5.2.2
Head 4.5.2.3
Level 4.5.2.4
4.5.2.5
4.5.2.6
4.5.2.7
Status display menu
371 ‫ﻳ ُﺗﺑ ﻊ ﻣ ﻥ ﺻ ﻔﺣﺔ‬
4. Settings
1 ->
4.1
4.2
4.3
4.4
4.5
4.6