Ryobi OHT-1850 Bedienungsanleitung Seite 18

GB
F D E I
C. RETAINING RING
D. WASHER
E. RETAINING PLATE
F. CUTTER BLADE ASSEMBLY
G. YOKES
H. CAMS
I. PINS
Fig. 9
A. CUTTER BLADE
B. GUARD
Fig. 10
A. BLADE COVER
OPERATION
TO INSTALL BATTERY PACK (NOT INCLUDED)
Place the battery pack in the hedge trimmer. Align raised rib
■
on battery pack with groove in hedge trimmer. See Figure 2.
Make sure the latches on the battery pack snap in place and
■
that battery pack is secured in hedge trimmer before
beginning operation.
TO REMOVE BATTERY PACK (NOT INCLUDED)
Locate latches of battery pack and depress to release the
■
battery pack from the hedge trimmer. See Figure 2.
Remove battery pack from the hedge trimmer.
■
CAUTION
When placing battery pack in your hedge trimmer, be
sure raised rib on battery pack aligns with groove in
hedge trimmer and latches snap in place properly.
Improper assembly of battery pack can cause damage
to internal components.
STARTING THE HEDGE TRIMMER
Remove the blade cover.
■
For added safety, there is a sensor switch in the upper
■
handle. See Fig. 3. When operating, hold the trimmer with
both hands, one hand to push the trigger lock button forward,
and the other hand to squeeze the front handle.
Release the trigger lock button and continue to squeeze the
■
trigger for extended operation.
STOPPING THE HEDGE TRIMMER
Release the trigger to stop the hedge trimmer.
■
Upon release of the trigger, the trigger lock button will be
■
automatically reset to the lock position.
OPERATING TIPS
Do not force the hedge trimmer through heavy shrubbery.
■
This can cause the blades to bind and slow down. If the
blades slow down, reduce the pace.
Do not try to cut stems or twigs that are larger than
■
P NL S DK N FIN GR HU CZ RU RO PL SLO HR TR EST LT
English
10 mm thick, or those obviously too large to feed into the
cutting blade. Use a non-powered hand saw or pruning saw
to trim large stems.
If desired, you can use a string to help cut your hedge level.
■
Decide how high you want the hedge. Then, stretch a piece
of string along the hedge at this height. Trim the hedge just
above this
See Figure 4. Trim the side of a hedge so that it will be slightly
narrower at the top. See Figure 5. More of the hedge will be
exposed when shaped this way, and it will be more uniform. If
blades do become jammed, stop the motor, allow the blades
to stop and remove the battery pack before attempting to
remove the obstruction.
Wear gloves when trimming thorny or prickly growth. When
■
trimming new growth, use a wide sweeping action, so that
the stems are fed directly into the cutting blade. Older growth
will have thicker stems and will be trimmed easiest by using a
sawing movement.
DANGER
If blade jams on any electrical cord or line,
DO NOT TOUCH THE BLADE! IT CAN BECOME
ELECTRICALLY LIVE AND VERY DANGEROUS.
Continue to hold the hedge trimmer by the insulated
rear handle or lay it down and away from you in a safe
manner. Disconnect the electrical service to the
damaged line or cord before attempting to free the
blade from the line or cord. Failure to heed this warning
will result in serious personal injury or possible death.
WARNING
Clear the area to be cut before each use.
Re-move all objects such as cords, lights, wire, or string
which can become entangled in the cutting blade and
create a risk of serious personal injury.
WARNING
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various Types
of commercial solvents and may be damaged by their
use. Use a clean cloth to remove dirt, oil, grease, etc.
When servicing use only identical Ryobi replacement
parts. Use of any other parts can create a hazard or
cause product damage.
CAUTION
Do not at any time let brake fluids, gasoline,
petroleum based products, penetrating oils, etc.,
come in contact with plastic parts. They contain
chemicals that may damage, weaken, or
destroy plastics.
13
LV
guide line of
SK BG
string.