Certificate Of Guarantee - Seac BCD Bedienungsanleitung

ASCENT
During your ascent, the air in your BC will expand, causing an
increase in positive lift and a consequent increase in speed. You
can control your buoyancy by pressing lightly on the deflation
button. If necessary you can use the inflator unit to limit and
control the speed of your ascent.
PRE-DIVE INSPECTION
 WARNING
During the ascent, it is crucial that the diver regulate
hydrostatic balance to avoid ascending too quickly.
Consult your instructor or dive manual for further
information about a safe speed of ascent. Always abide
by the standards dictated by your dive computer or
decompression tables during all stages of the dive.
 WARNING
We r e c o m m e n d t h a t yo u u s e t h e B C o n l y a s
a compensator for your buoyancy. Using the BC to
lift heavy objects from the seabed can be extremely
dangerous and lead to uncontrolled ascents that can
result in serious accidents for the diver and his or her
buddies.
MAINTENANCE
The following instructions are vital to keep your BC operating
perfectly:
• After every dive, both in the ocean or in the pool, always
rinse the BC inside and out with fresh water, and make sure
you have cleared out any remaining water using the over-
expansion relief valve.
• Never store the BC with other equipment or objects that are
sharp and could puncture the buoyancy bag.
• Do not store the BC wet or folded; always allow it to dry fully.
Carefully wash the inside, drain out the water, and when the
BC is completely dry store it in a cool, ventilated place.
• At the end of each dive, always replace the protective cap on
the quick coupling after having disconnected the hose.
• Avoid leaving the BC exposed to the sun for long periods.
• Carefully rinse all the inflation and deflation mechanisms with
fresh water.
To clean the inside of the BC, proceed as follows:
- Unscrew the over-expansion relief valve and add fresh water
(about 1/4 the volume of the BC).
- Replace the over-expansion relief valve.
- Inflate the BC, turning it upside down and shaking side to side
to circulate the water around inside.
- Turn the bag so the corrugated hose points downward and
press the inflation button. This will empty all the water through
the mouthpiece.
 WARNING
In cleaning the BC, do not use any type of solvents or
cleaning products.
B C D m a n u a l | I n s t r u c t i o n
USE OF THE BCS WITH OXYGEN-RICH
MIXTURES
 WARNING
SEAC Jackets, if used with breathable air in accordance
with EN 12021, are considered to conform to EU
Category Regulation 2016/425. The instructions for
use are provided in the enclosed manual and refer to
use of the BC with breathable air according to EN 12021
(oxygen content of 21±2%). Because to date there are
no regulations for verifying by means of adequate and
meaningful tests that the essential safety requirements
prescribed by EU Category Regulation 2016/425 have
been met, this SEAC BCD is not be to considered EC
Certified under (EU) Category Regulation 2016/425 for
use with oxygen rich mixtures (O2 > 21±2%).
 WARNING
Do not use any SEAC BC with oxygen rich mixtures
(Nitrox - Maximum ox ygen content: 40%) without
having first received adequate training on their use:
Failure to observe this warning may result in a serious
accident.
 WARNING
Do not use this SEAC BC with other gases or with
oxygen-rich mixtures. SEAC BCs are designed only
for use with compressed atmospheric air. Failure to
observe this warning may result in premature wear of
the equipment, defective operation, or risk of explosion,
resulting in potentially serious damage.

CERTIFICATE OF GUARANTEE

SEAC guarantees the correct operation of this product as
described in this document.
The warranty has a duration of 2 (two) years in accordance with
current European regulations.
The warranty herein can be exercised according to the conditions
and limits expressly indicated below:
1. The warranty has a duration of 2 (two) years starting from the
time the product is purchased at a SEAC authorized dealer and
requires no prior or subsequent formal validation.
2. The warranty is acknowledged only to the original buyer of the
product at a SEAC authorized dealer.
The warranty is strictly personal, and cannot be transferred to a
third party without express advance authorization from SEAC.
3. The warranty covers all, and only, malfunctions due to:
• Materials found to be unsuitable
• Evident design errors
• Fabrication or assembly of the product or its parts
• Incorrect or inadequate instructions and recommendations for
use.
4. The warranty terminates automatically, and with immediate
effect, following any repairs, modifications, transformations,
adjustments or tampering in general, carried out on the finished
product or parts of it, that were not authorized in advance by
SEAC or were carried out by non-authorized personnel.
5. The warranty entitles you to intervention and free repair in
the shortest possible time, or to a full free replacement of the
product (at the sole discretion of SEAC) or parts of it whenever
a malfunctioning defect specifically described in item 3 above
is acknowledged by SEAC.
6. This warranty may also be exercised by shipping the product
believed to be defective to SEAC.
21