Certificate Of Guarantee - Seac SIDEMOUNT Anweisung

PRE-DIVE INSPECTION
During the ascent, it is crucial that the diver regulate hydrostatic balance to
avoid ascending too quickly. Consult your instructor or dive manual for further
information about a safe speed of ascent. Always abide by the standards dictated
by your dive computer or decompression tables during all stages of the dive.
We recommend that you use the Sidemount BC only as a compensator for your
buoyancy. Using the Sidemount BC to lift heavy objects from the seabed can be
extremely dangerous and lead to uncontrolled ascents that can result in serious
accidents for the diver and his or her buddies.
MAINTENANCE
The following instructions are vital to keep your Sidemount BC operating perfectly:
• After every dive, both in the ocean or in the pool, always rinse the BC inside and out
with fresh water, and make sure you have cleared out any remaining water using the
over-expansion relief valve.
• Never store the Sidemount BC with other equipment or objects that are sharp and
could puncture the buoyancy bag.
• Do not store the Sidemount BC wet or folded; always allow it to dry fully. Carefully wash
the inside, drain out the water, and when the BC is completely dry store it in a cool,
ventilated place.
• At the end of each dive, always replace the protective cap on the quick coupling after
having disconnected the hose.
• Avoid leaving the Sidemount BC exposed to the sun for long periods.
• Carefully rinse all the inflation and deflation mechanisms with fresh water.
To clean the inside of the BC, proceed as follows:
- Unscrew the over-expansion relief valve and add fresh water (about 1/4 the volume of
the BC).
- Replace the over-expansion relief valve.
- Inflate the BC, turning it upside down and shaking side to side to circulate the water
around inside.
- Turn the bag so the corrugated hose points downward and press the inflation button.
This will empty all the water through the mouthpiece.
In cleaning the Sidemount BC, do not use any type of solvents or cleaning products.
20 English
11661-SEAC-MANUALE JACKET sidemount-totale.indb 20
 WARNING
 WARNING
 WARNING
USE OF THE SIDEMOUNT BCs WITH OXYGEN-RICH MIXTURES
 WARNING
This product was designed and created for use with compressed atmospheric
air or Nitrox blends up to a maximum percentage of 40% oxygen content.
The use of blends with an oxygen percentage greater than 40% and/or made
with other gases (such as added helium), can cause damage or deterioration in
the BC and compromise its proper operation.
 WARNING
Do not use any SEAC Sidemount BC with ox ygen rich mix tures (Nitrox -
Maximum oxygen content: 40%) without having first received adequate training
on their use: Failure to observe this warning may result in a serious accident.
 WARNING
Do not use this SEAC Sidemount BC with other gases or with oxygen-rich
mixtures. SEAC BCs are designed only for use with compressed atmospheric air.
Failure to observe this warning may result in premature wear of the equipment,
defective operation, or risk of explosion, resulting in potentially serious damage.

CERTIFICATE OF GUARANTEE

SEACSUB S.p.A. guarantees the correct operation of this product as described in this
document.
The warranty has a duration of 2 (two) years in accordance with current European
regulations.
The warranty herein can be exercised according to the conditions and limits expressly
indicated below:
1. The warranty has a duration of 2 (two) years starting from the time the product is
purchased at a SEAC authorized dealer and requires no prior or subsequent formal validation.
2. The warranty is acknowledged only to the original buyer of the product at a SEAC
authorized dealer.
The warranty is strictly personal, and cannot be transferred to a third party without express
advance authorization from SEAC.
3. The warranty covers all, and only, malfunctions due to:
• Materials found to be unsuitable.
• Evident design errors.
• Fabrication or assembly of the product or its parts.
• Incorrect or inadequate instructions and recommendations for use.
4. The warranty terminates automatically, and with immediate effect, following any
repairs, modifications, transformations, adjustments or tampering in general, carried out
on the finished product or parts of it, that were not authorized in advance by SEAC or were
carried out by non-authorized personnel.
15/06/2015 09.24.10