R Balance (Balance Of The Left And Right Main Speakers); Hp Tone Ctrl (Headphone Tone Control); Center Geq (Center Graphic Equalizer) - Yamaha RX-V1300RDS Bedienungsanleitung

3
Press d to go to "FRQ" and press j / i to
select the frequency you want to use.
2 LOW FRQ TEST
T E S T T O N E ... ... ... O F F
O U T P U T ... M A I N L / R
≥ F R Q ... ... ... ... ... ... ... ... 8 8 H z
4
Adjust the volume of the subwoofer with the
controls on the subwoofer so it matches that
of the speaker you are comparing it to.
I About the test tone
The test tone is produced by the tone generator.
The tone generator produces a narrow-band noise
centered on a specified frequency by the band pass filter
besides a wide-band noise.
You can change this center frequency from 35 Hz through
250 Hz in one-sixth octave steps.
You can use the test tone not only for adjusting the
subwoofer level, but also for checking the low-frequency
characteristics of your listening room. Low-frequency
sounds are especially affected by the listener's position,
speaker placement, subwoofer polarity and other
conditions.
Digital generator
(wide band noise produced)
Center freq.
Band pass filter
3 L/R BALANCE (balance of the
left and right main speakers)
Use this feature to adjust the balance of the output level
from the left and right main speakers.
Control range: 10 steps for L/R
Initial setting: 0 dB for L/R
Press i to decrease the output level for the
left main speaker. Press j for the right main
speaker.
3 L/R BALANCE
L ........................ ........................R
- / + : A d j u s t
/
0109V1300_56-68_EN-GB.p65
Noise
Freq.
35 Hz – 250 Hz
0
: E x i t
61
4 HP TONE CTRL (headphone tone
control)
Use this feature to adjust the level of the bass and treble
when you use your headphones.
Control range (dB): –6 to +3 for both BASS and TRBL
(treble)
Initial setting: 0 dB for both BASS and TRBL (treble)
4 HP TONE CTRL
≥ B A S S
T R B L
-
5 CENTER GEQ (center graphic
equalizer)
Use this feature to adjust the built-in 5-band graphic
equalizer so that the center speaker tonal quality matches
that of the left and right main speakers. You can select the
100 Hz, 300 Hz, 1 kHz, 3 kHz, or 10 kHz frequencies.
Control range (dB): –6 to +6
Initial setting: 0 dB for 5-band
1
Press d to select a higher frequency and u
to select a lower frequency.
5 CENTER GEQ
≥ 1 0 0 H z
3 0 0 H z
1 k H z
3 k H z
1 0 k H z
-
2
Press j / i to adjust the level of that
frequency.
5 CENTER GEQ
1 0 0 H z
≥ 3 0 0 H z
1 k H z
3 k H z
1 0 k H z
-
+ 3 d B
y
• You can monitor the center speaker sound while adjusting this
item by using the test tone. Press TEST before starting the
foregoing procedure. "TEST DOLBY SUR." appears on the
video monitor, and the test tone starts alternating among the
speakers. Once you begin this procedure, the test tone remains
at the center speaker and you can hear how the sound changes
as you adjust the various frequency levels. To stop the test tone,
press TEST (see pages 24, 25).
2002.11.07, 12:09
SET MENU
+
0 d B
+
0 d B
+
61