Basic Recording - Yamaha RX-V1300RDS Bedienungsanleitung

Recording adjustments and other operations are
performed from the recording components. Refer to the
operation instructions for these components.
2
NATURAL SOUND AV RECEIVER RX-V1300RDS
STANDBY
/ON
6CH INPUT MODE
TUNER
SPEAKERS BASS PROCESSOR
EXTENSION DIRECT
A B
DSP
2
1
Turn on the power of this unit and all
connected component.
2
Select the source component you want to
record from.
INPUT
Front panel
3
Start playback (or select a broadcast station)
on the source component.
4
Start recording on the recording component.
44
0107V1300_38-44_EN-GB.p65

BASIC RECORDING

VOLUME
D I G I T A L
PRESET/ PRESET TUNING RDS MODE
A/B/C/D/E TUNING /TUNING FM/AM MEMORY MODE /FREQ BASS
EON PTY SEEK
EDIT MAN'L/AUTO FM AUTO/MAN'L MONO
MODE START
PHONES S VIDEO VIDEO L AUDIO R OPTICAL
STEREO PROGRAM
EFFECT
SILENT VIDEO AUX
– + –
TRANSMIT RE–NAME CLEAR LEARN
SYSTEM
POWER STANDBY SLEEP 6CH INPUT
A PHONO TUNER CD
V-AUX CBL/SAT MD/TAPE CD-R
D- TV/LD VCR 1 VCR2/DVR DVD
SELECT
POWER POWER AMP
TV AV
REC
PHONO TUNER CD
A
V-AUX CBL/SAT MD/TAPE CD-R
or
D-TV/LD VCR 1 VCR2/DVR DVD
Remote control
44
Notes
• Do a test recording before you start an actual recording.
• When this unit is set in the standby mode, you cannot record
between other components connected to this unit.
• The setting of BASS, TREBLE, BASS EXTENSION,
VOLUME, "3 L/R BALANCE" on the SET MENU and DSP
programs does not affect the recorded material.
• A source connected to the 6CH INPUT jacks of this unit
cannot be recorded.
• S-video and composite video signals pass independently
TREBLE
through this unit's video circuits. Therefore, when recording or
dubbing video signals, if your video source component is
+
connected to provide only an S-video (or only a composite
video) signal, you can record only an S-video (or only a
composite video) signal by your VCR.
• A given input source is not output on the same REC OUT
channel. (For example, the signal input from VCR 1 IN is not
output on VCR 1 OUT.)
• Check the copyright laws in your country to record from
records, CDs, radio, etc. Recording of copyrighted material
may infringe copyright laws.
I Special considerations when
recording DTS software
The DTS signal is a digital bitstream. Attempting to
digitally record the DTS bitstream will result in noise
being recorded. Therefore, if you want to use this unit to
record sources that have DTS signals recorded on them,
the following considerations and adjustments need to be
made.
For LDs, DVDs and CDs encoded with DTS, when your
player is compatible with the DTS format, follow its
operation instruction to make a setting so that the analog
signal will be output from the player.
I Timer playback/recording
This unit can perform playback or recording with an
external timer (not supplied). Refer to the operation
instruction for the component and the timer to be used.
Notes
• The stored data such as input source will be reflected in the
playback or recording with the timer.
• If you do not want any sound output during the recording with
a timer, turn the volume down.
Memory back-up
The memory back-up circuit prevents the stored data
(input source, volume level, set menu settings and so
on) from being lost even if this unit is in the standby
mode (disconnected from the AC outlet). However if
the timer is turned off for more than one week, the
stored data will be lost.
2002.11.07, 12:08