Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
0.1
1
10
100
For transmitters rated at a maximum output power not listed above, the recommended separation distance (D) in meters
(m) can be determined using the equation applicable to the frequency of the transmitter, where P is the maximum output
power rating of the transmitter in watts (W) according to the transmitter manufacturer.
N N o o t t e e 1 1 - At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
N N o o t t e e 2 2 - These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects, and people.
The electric lift option, electric litter option, or scale system option is intended for use in the electromagnetic environment
specified below. The customer or the user of the electric lift option, electric litter option, or scale system option should
assure that it is used in such an environment.
I I m m m m u u n n i i t t y y t t e e s s t t
Electrostatic Discharge
(ESD)
IEC 61000-4-2
Electrostatic fast transient/
burst
IEC 61000-4-4*
Surge
IEC 61000-4-5*
Voltage dips, voltage
variations and short
interruptions on power
supply input lines
IEC 61000-4-11*
Power frequency (50/60 Hz)
magnetic field
IEC 61000-4-8
Note: U
is the AC mains voltage before application of the test level.
t
*Applies to the electric lift option or electric litter option only.
1105-409-005 Rev E.1
G G u u i i d d a a n n c c e e a a n n d d m m a a n n u u f f a a c c t t u u r r e e r r ' ' s s d d e e c c l l a a r r a a t t i i o o n n - - e e l l e e c c t t r r o o m m a a g g n n e e t t i i c c i i m m m m u u n n i i t t y y
I I E E C C 6 6 0 0 6 6 0 0 1 1 t t e e s s t t l l e e v v e e l l
±8 kV contact
±15 kV air
±2 kV for power supply lines
±1 kV for input/output lines
±1 kV line(s) to line(s)
±2 kV line(s) to earth
0% U
for 0.5 cycle at 0°,
T
45°, 90°, 135°, 180°, 225°,
270°, and 315°
0% U
for 1 cycle
T
70% U
(30% dip in U
T
25 cycles
0% U
for 250 cycles
T
30 A/m
0.38
1.2
3.8
12
C C o o m m p p l l i i a a n n c c e e l l e e v v e e l l
±8 kV contact
±15 kV air
±2 kV for power supply lines
±1 kV for input/output lines
±1 kV line(s) to line(s)
±2 kV line(s) to earth
0% U
for 0.5 cycle at 0°,
T
45°, 90°, 135°, 180°, 225°,
270°, and 315°
0% U
for 1 cycle
T
) for
70% U
(30% dip in U
T
T
25 cycles
0% U
for 250 cycles
T
30 A/m
0.38
1.2
3.8
12
E E l l e e c c t t r r o o m m a a g g n n e e t t i i c c
e e n n v v i i r r o o n n m m e e n n t t g g u u i i d d a a n n c c e e
Floors should be wood,
concrete, or ceramic tile. If
floors are covered with
synthetic material, the
relative humidity should be
at least 30%.
Mains power quality should
be that of a typical
commercial or hospital
environment.
Mains power quality should
be that of a typical
commercial or hospital
environment.
Mains power quality should
be that of a typical
commercial or hospital
environment. If the user of
the electric lift option or
electric litter option requires
) for
T
continued operation during
power mains interruptions, it
is recommended that the
device be powered from an
uninterrupted power supply
or a battery.
Power frequency magnetic
fields should be at levels
characteristic of a typical
location in a typical
commercial or hospital
environment.
0.73
2.3
7.3
23
53
EN
Werbung
Inhaltsverzeichnis
