Herunterladen Inhalt Inhalt Diese Seite drucken

Electrical Safety - Black+Decker KA280 Bersetzung Der Ursprünglichen Anweisungen

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 13
Injuries caused when changing any parts, blades or ac-
u
cessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN62841
and may be used for comparing one tool with another. The
declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following symbols are shown on the tool along with the
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.

Electrical safety

#
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Autoselect® dial
3. Base / speed setting indicator
4. Base release button
(Original instructions)
5. Random orbital sanding base
6. Large detail sanding base
7. Sanding base tip
8. Detail finger attachment
9. Dust canister
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Removing sanding bases (fig. A)
To remove the sanding base, press the release button (4)
u
and pull the base (6) from the tool.
Attaching the random orbit sanding base (fig. B)
Hold the tool and the sanding base (5) facing upwards
u
as shown in fig. B.
Align the dust openings (10) in the sanding base with
u
the dust openings (11) in the tool base.
Press in on the sanding base until you hear it click into
u
place.
Fitting sanding sheets (fig. C)
Hold the tool with the sanding base (5) facing upwards.
u
Place the sanding sheet (12) onto the sanding base (5)
u
making sure that the holes in the sheet line up with the
holes in the base.
Large detail sanding base
With this sanding base, you can use the tool as a detail
sander or a flush sander.
Attaching the large detail sanding base (fig. D & E)
For detail sanding, the pointed end should face forward
(fig. D).
For sanding large areas, the pointed end should face to the
rear (fig. E).
Attach the sanding base as described above under
u
"Attaching the random orbit sanding base".
Press in on the sanding base until you hear it click into
u
place.
Fitting sanding sheets (fig. F)
Detach the two diamond-shaped tips (13) from the
u
sanding sheet (14).
Hold the tool with the sanding base facing upwards.
u
Place the sanding sheet (14) onto the sanding base,
u
making sure that the holes in the sheet line up with the
holes in the base.
The diamond-shaped tip (15) can be reversed and replaced
when worn.
ENGLISH
7

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis