Operation; Maintenance; Troubleshooting - Roller Akku-Picco P 40 Betriebsanleitung

eng
1.8. Vibrations
Weighted effective value of acceleration
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used by way of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminary evaluation of the exposure.
Attention: The indicated weighted effective value of acceleration can differ
during operation from the indicated value, dependent on the manner in which
the device is used. Dependent upon the actual conditions of use (periodic duty)
it may be necessary to establish safety precautions for the protection of the
operator.
2. Preparations for use
Electrical connection
Note the mains voltage! Before connecting the drive unit or the rapid charger,
check whether voltage on the rating plate matches the mains voltage. At work
sites, in damp surroundings, in the open or in the case of comparable types of
use, only operate the equipment off the mains using a 30mA fault current
protected switch (FI breaker).
Charge the battery before initial operation. Only use the supplied charger with
the cordless pipe shears the ROLLER'S Akku-Picco P 40. Insert the plug of
the charging unit into the socket (1) on the under side of the hand grip (2). Insert
the mains plug of the charging unit into the mains socket. Allow the battery 2
hours to charge. After charging unplug the mains plug first, then the plug from
the socket connecting the charger (1).
The battery reaches full capacity after several charges. The charger is not
suitable for use outside.

3. Operation

Warning, risk of injury!
Never grip in the area of the blade (3)! There is a danger of losing your finger!
Keep hair, clothes and gloves well away from the cutting area.
3.1. Working procedure
Mark where the cut is to be made on the pipe. Slide switch "ON/OFF" (4) should
be switched to the "ON" position. Rest the pipe on the pipe support (5) and
press against the safety switch (6). Engage the safety tip switch (trigger) (7).
The blade (3) cuts through the pipe. After cutting the cordless pipe shears shuts
off automatically, as long as the safety tip switch (trigger) is released (6). By
pressing the return button (8) the blade (3) retracts.
Switch the slide switch to "OFF", when you have finished using the ROLLER'S
Akku-Picco P 40. Charge the battery again ready for the next usage.

4. Maintenance

Before any maintenance or servicing switch the slide switch (4) to the "OFF"
position! This work should be carried out only be service professionals and
trained personell.
4.1. Inspection/maintenance
The motor has carbon brushes, which are subject to wear. Therefore the cord-
less pipe shears must be inspected from time to time by an authorised ROLLER
service repair depot. The carbon brushes cannot be replaced, in which case
the motor would need to be replaced.
4.2. Replacing the blade (3)
Switch the slide switch (4) to the "OFF" position! Place the cordless pipe shears
down so that the housing screws can be removed. Remove the upper housing.
Remove the fixing screw of the drive-unit and remove the drive-unit. Remove
the spring for the blade return. Remove all nuts of the blade holder, replace the
blade. Lightly oil moving parts.

5. Troubleshooting

5.1. Fault
Cordless pipe shears halt during cutting procedure.
Cause
● Material is not suitable for cutting with the ROLLER'S Akku-Picco P 40.
● Battery low or flat.
● Blade blunt.
5.2. Fault
Cordless pipe shears does not operate when safety tip switch (trigger) is
pressed.
Cause
● Safety switch ON/OFF is in the "OFF" position.
● Pipe is not in contact with the safety switch.
● Battery low or flat.
● Blade blunt.
6. Manufacturer's Warranty
The warranty period shall be 12 months from delivery of the new product to the
first user but shall be a maximum of 24 months after delivery to the Dealer. The
date of delivery shall be documented by the submission of the original purchase
documents, which must include the date of purchase and the designation of
the product. All functional defects occurring within the warranty period, which
clearly the consequence of defects in production or materials, will be remedied
2.5 m/s² free of charge. The remedy of defects shall not extend or renew the guarantee
period for the product. Damage attributable to natural wear and tear, incorrect
treatment or misuse, failure to observe the operational instructions, unsuitable
operating materials, excessive demand, use for unauthorized purposes, inter-
ventions by the Customer or a third party or other reasons, for which ROLLER
is not responsible, shall be excluded from the warranty.
Services under the warranty may only be provided by customer service stations
authorized for this purpose by ROLLER. Complaints will only be accepted if
the product is returned to a customer service station autho rized by ROLLER
without prior interference in an unassembled condition. Replaced products and
parts shall become the property of ROLLER.
The user shall be responsible for the cost of shipping and returning the product.
The legal rights of users, in particular the right to claim damages from the
Dealer, shall not be affected. This manufacturer's warranty shall apply only to
new products purchased in the European Union, in Norway or Switzerland.
7. EC declaration of conformity
ROLLER declares that the products decribed in this user manual comply with
corresponding directives 98/37/EG, 2004/108/EG, 2006/42/EG and 73/23/EWG.
Correspondingly this applies to the following norms: DIN EN ISO 12100-1, DIN
EN 12348, DIN EN 50144-1, DIN EN 55014-1, DIN EN 55014-2, DIN EN
60204-1, DIN EN 60335-1, DIN EN 60335-2-45, DIN EN 60745-1, DIN EN
60745-2-9, DIN EN 60745-2-11, DIN EN 61000-3-2, DIN EN 61000-3-3, DIN
EN 61029-1, DIN EN 61029-2-9, DIN/ISO 3744.
Waiblingen, 01.12. 2009
Albert ROLLER GmbH & Co KG
Manufacturer of Tools and Machines
D-71332 Waiblingen
Rainer Hech
8. Spare parts lists
Spare parts lists see www.albert-roller.de under Downloads.
eng