Initial Operation - Bosch PowerPack 300 Originalbetriebsanleitung

OBJ_BUCH-2074-001.book Page 2 Wednesday, August 14, 2013 12:19 PM
Indication Elements, HMI
a Motor-output indicator
b Assistance-level indicator
c Illumination indicator
d Text indication
e Value indication
f Speed indication
g Battery charge-control indicator
Technical Data
Drive Unit
Article number
Rated continuous output
Torque at drive, max.
Rated voltage
Operating temperature
Storage temperature
Degree of protection
Weight, approx.
HMI
Article number
Max. charging current,
USB connection
Charging voltage,
USB connection
Operating temperature
Storage temperature
Charging temperature
Degree of protection
Weight, approx.
Lighting*
Rated voltage
Power output
– Front light
– Rear light
* Not possible via the eBike battery pack in all country-specific versions,
depending on the statutory regulations
Assembly
Inserting and Removing the Battery Pack
For inserting and removing the battery pack in/from the eBike,
please read and observe the battery pack operating instruc-
tions.
Bosch eBike Systems
Inserting and Removing the HMI (see figure A)
To insert the HMI 3, slide it from the front into the holder 4.
To remove the HMI 3, press the lock latch 15 and slide the
HMI toward the front out of the holder 4.
 Remove the HMI when you park the eBike.
It is possible to secure the HMI against removal in the holder.
To do so, remove the holder 4 from the handlebars. Put the
HMI in the holder. Screw the locking screw 16 (thread M3,
8 mm long) from below into the thread provided in the holder.
Mount the holder back onto the handlebars.
Drive Unit
Checking the Speed Sensor (see figure B)
0 275 007 020
The speed sensor 17 and its spoke magnet 18 must be
0 275 007 022
mounted in such a manner that the spoke magnet, after a turn
W 250
of the wheel, moves past the speed sensor with a clearance of
Nm 48
at least 5 mm, yet no more than 17 mm.
V 36
Note: If the clearance between speed sensor 17 and spoke
°C –5...+40
magnet 18 is too small or too large, or if the speed sensor 17
is not properly connected, the speed indication f will fail, and
°C –10...+50
the eBike drive will operate in emergency mode.
IP 54 (dust and splash
In this case, loosen the screw of the spoke magnet 18 and fas-
water protected)
ten the spoke magnet to the spoke in such a manner that it
kg 4
runs past the mark of the speed sensor at the correct clear-
ance. When the speed is still not being indicated in the speed
Intuvia
indication f after this, please refer to an authorised bicycle
1 270 020 906
dealer.
Operation
mA 500

Initial Operation

V 5
°C –5...+40
Requirements
The eBike system can only be activated when the following
°C –10...+50
requirements are met:
°C 0...+40
– A sufficiently charged battery pack is inserted (see operat-
IP 54 (dust and splash
water protected)
– The HMI is properly inserted in the holder (see "Inserting
kg 0.15
– The HMI is properly connected (see "Checking the Speed
V 6
Switching the eBike System On/Off
Options for switching on the eBike system:
W 6.6
– If the HMI is already switched on when inserted into the
W 0.6
– When the HMI and the battery pack are inserted, briefly
– When the HMI is inserted, press the On/Off button of the
The drive is activated as soon as you step into the pedals (ex-
cept when in push-assistance mode, see "Switching the Push-
assistance mode On/Off", page English–4). The motor out-
put depends on the settings of the HMI.
ing instructions of the battery pack).
and Removing the HMI", page English–2).
Sensor", page English–2).
holder, then the eBike system will be switched on automat-
ically.
press the On/Off button 5 of the HMI once.
battery pack (see battery pack operating instructions).
English–2
0 276 001 SAI | (14.8.13)