DAB e.sybox Bedienungs Und Wartungsanweisungen Seite 60

GB
ENGLISH
INDEX
Key
Warnings
Responsibility
1. General
1.1 Description of the Integrated Inverter
1.2 Integrated expansion vessel
1.3 Integrated electropump
1.4 Technical characteristics
2. Installation
2.1 Vertical Configuration
2.1.1 Hydraulic connections
2.1.2 Loading operation – Installation above head and below head
2.2 Horizontal configuration
2.2.1 Hydraulic connections
2.2.2 Orientation of the interface panel
2.2.3 Loading operation – Installation above head and below head
3. Commissioning
3.1 Electrical connections
3.2 Configuration of the integrated inverter
3.3 Priming
4. Protection systems
4.1 Description of blockages
4.1.1 "BL" AAnti Dry-Run (Protection against dry running)
4.1.2 Anti-Cycling (Protection against continuous cycles without utility request)
4.1.3 Anti-Freeze (Protection against freezing of water in the system)
4.1.4 "BP1" Blockage due to fault of the internal pressure sensor
4.1.5 PB" Blockage due to line voltage outside specifications
4.1.6 "SC" Blockage due to short circuit between the motor phases
4.2 Manual reset of error conditions
4.3 Self-reset of error conditions
5. Inverter electronic control and user interface
5.1 Operation with control unit
5.1.1 Functions made available by control units
5.1.2 Electrical connections of utility inputs and outputs
5.1.3 Safety mode operation
5.1.4 Control unit function setup
5.1.5 Association and disassociation of e.sybox and control unit
6. The keypad and the display
6.1 Direct access with a combination of keys
57
6.2 Access by name with a drop-down menu
6.3 Structure of the menu pages
6.4 Blocking parameter setting by Password
60
6.5 Enabling and disabling the motor
60
61 7. Meaning of the individual parameters
7.1 User Menu
61
7.1.1 Status
62
7.1.2 RS: Rotation speed display
62
7.1.3 VP: Pressure display
63
7.1.4 VF: Flow display
64
7.1.5 PO: Absorbed power display
7.1.6 C1: Phase current display
65
7.1.7 Operating hours and number of starts
65
66 7.1.8 PI: Power histogram
7.1.9 Multi-pump system
67
67 7.1.10 Output flow meter
68 7.1.11 VE: Version display
68 7.1.12 FF: Fault log display
69 7.2 Monitor Menu
7.2.1 CT: Display contrast
69
7.2.2 BK: Display brightness
69
7.2.3 TK: Backlight switch-on time
70
7.2.4 LA: Language
70
7.2.5 TE: Dissipator temperature display
7.3 Setpoint Menu
71
7.3.1 SP: Setting the setpoint pressure
71
71 7.3.2 Setting the auxiliary pressures
7.3.2.1 P1: Setting the auxiliary setpoint 1
72
7.3.2.2 P2: Setting the auxiliary setpoint 2
72
7.3.2.3 P3: Setting the auxiliary setpoint 3
72
7.3.2.4 P4: Setting the auxiliary setpoint 4
72
72 7.4 Manual Menu
7.4.1 Status
73
73 7.4.2 RI: Speed setting
7.4.3 VP: Pressure display
73
7.4.4 VF: Flow display
73
7.4.5 PO: Absorbed power display
74
7.4.6 C1: Phase current display
74
7.4.7 RS: Rotation speed display
74
7.4.8 TE: Dissipator temperature display
75
7.5 Installer Menu
75
7.5.1 RP: Setting the pressure fall to restart
7.5.2 OD: Type of plant
76
7.5.3 AD: Address configuration
77
80
81
82
82
82
82
82
82
82
82
83
83
83
83
83
83
83
83
84
84
84
84
84
84
84
84
84
85
85
85
85
85
85
85
86
86
86
86
86
86
86
86
86
86