Bionaire BAOF25W Betriebsanleitung Seite 2

BAOF25M/W/30M/W/BI06MLM1.qxd 11/2/06 3:43 PM Page 4
BAOF25M/BAOF25W
BAOF30M/BAOF30W/BAOF30B
Fig.1
M D
L
H
J
F
N
O
ENGLISH
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety
precautions should always be taken including
the following:
• Use the fan only for purposes described in the
instruction manual.
• To protect against electrical shock, do not
immerse the fan, plug or mains cable in water
or spray with liquids.
K
• Close supervision is necessary when any
appliance is used by or near children.
P
• Unplug from the electrical outlet when not in
use, when moving the fan from one location to
G
another, before putting on or taking off parts
and before cleaning.
Q
• Avoid contact with any moving parts.
• Do not operate in the presence of explosive
and/or flammable fumes.
E
• Do not place the fan or any parts near an open
flame, cooking or other heating appliance.
• Do not operate any appliance with a damaged
mains cable, plug, after the appliance
malfunctions, or has been dropped/ damaged
in any manner.
I • The use of attachments not recommended or
sold by the appliance manufacturer may
A cause hazards.
• Do not use outdoors.
• Do not let the mains cable hang over the edge
of a table or counter, or come into contact with
B hot surfaces.
• To disconnect from the electrical supply, grip
the plug and pull from the wall outlet. DO NOT
pull on the mains cable.
C
• Always use on a dry, level surface.
• Do not operate without the fan grills properly
in place.
• This product is intended for household use ONLY
and not for commercial or industrial applications.
• If the supply cord or plug is damaged, it must
be replaced by the manufacturer or its service
agent or a similarly qualified person in order to
avoid hazard.
• The appliance contains no user serviceable
parts and should the product suffer damage
or breakdown it must be returned to the
manufacturer or its service agent.
• Should the appliance stop working, first check the
fuse in the plug (UK only) or fuse/circuit breaker at
the distribution board is operating, before
contacting the manufacturer or service agent.
NOTE: Use caution when adjusting the tilt
angle of the fan head to ensure that your
fingers do not get caught.
MISSING A PART FOR YOUR FAN?
not on the grills themselves). Finish securing
the grill ring in the same manner until both
Please call 0800 052 3615 for assistance.
grills are joined underneath the black ring.
ASSEMBLY INSTRUCTIONS
9. Tighten the screw.
See Fig. 1
OPERATING INSTRUCTIONS (See Fig. 1)
A. upper body
1. Set the fan base on a dry level surface.
B. Base
2. Make sure the Speed Control is in the OFF
C.Screw/ Spring Washer / Flat Washer (4)
(0) position. Speed Control (P) is located on
the top of the fan motor housing.
D.Mounting Nut
3. Plug the cord into a suitable outlet.
E. Motor Housing
4. The SPEED is adjusted by turning the Speed
F. Rear Grill
Control to the desired setting:
G.Motor Shaft
0
H.Notches
I
I. Prong
II
J. Fan Blade
III
K. Flat
ADJUSTMENT
L. Locking Screw
M.Grill Ring Tilt adjustment
N.Front Grill
To change the tilting angle of the fan head,
O.Fixing Screw
simply move the fan head to the desired angle.
P. Speed Control Oscillation adjustment
Q.Oscillation Control
The OSCILLATION control (Q) is located on the
1. Fit the upper body (A) to the base (B). Align top of the fan motor housing. To start oscillation,
the 4 screw holes in the base to the four holes push the control knob down. To stop oscillation,
in the upper body. Fix securely with the 4 sets pull the control knob up.
of screw, spring washer and flat washer (C).
CLEANING AND MAINTENANCE
2. Unscrew the rear grill mounting nut (D) from
the motor housing (E). Position the rear grill • Always unplug the fan before cleaning or
disassembly.
(F) over the motor shaft (G), making certain 2
notches (H) at the sides of the rear grill fit
• Do not allow water to drip on or into the fan
over the corresponding prongs (I) on the motor housing.
motor housing. Please make sure the rear grill
FAN STORAGE
fits securely against the motor housing.
3. Secure the rear grill in its place using the rear It is important to keep the fan in a safe, dry location.
grill mounting nut. Turn this nut clockwise and
• We recommend using the original (or
tighten firmly.
appropriately sized) box.
4. Remove the protective sleeve from the motor shaft.
FITTING A REPLACEMENT PLUG
5. Slide the fan blade (J), with the fixing screw FOR U.K. AND IRELAND ONLY
facing towards the rear grill, firmly onto the
If the plug is not suitable for the socket outlets in
motor shaft, aligning the screw with the flat (K)
your home, it can be removed and replaced by a
on the motor shaft.
plug of the correct type. Please refer to "Installation
6. Position the locking screw (L) over the flat on
of a plug" below.
the motor shaft. Tighten the screw into the
Installation of a plug Applicable to U.K.
side hole of the fan blade, against the motor
and Ireland.
7. Loosely fit the grill ring (M) to the front grill
WARNING - THIS APPLIANCE MUST BE
(N). Position the fixing screw (O) at the bottom
EARTHED.
of the grill with reference to the Bionaire ® logo.
The grill ring has two grooves. Locate the The wires in the mains lead are coloured as such:
front grill to one of these grooves leaving the GREEN AND YELLOW
other groove free to attach to the rear grill.
BROWN
Only tighten the fixing screw enough to hold
BLUE
the grill ring in place.
Please note that the colour of these mains wires
8. Centre the front grill by aligning the Bionaire ®
may not correspond with the colour markings
logo on the logo plate so that it is horizontal
that identify the terminals in your plug.
and parallel with the floor. Then, holding the
Please proceed as follows:
front grill against the rear grill, push the black
grill ring into place at the top and bottom of
the fan. (Push directly on the black grill ring,
2
The wire which is coloured GREEN AND YELLOW
must be connected to the terminal which is marked
with the letter 'E' or by the earth symbol
coloured GREEN or GREEN AND YELLOW.
The BROWN coloured wire must be connected
to the terminal, which is marked with the letter
"L" or is coloured RED.
The BLUE coloured wire must be connected to
the terminal, which is marked with the letter "N"
or is coloured BLACK.
- Off
- Low
- Med
- High
NOTE: If the terminals in the plug are not marked
or if you are unsure or in doubt about the installation
of the plug please contact a qualified electrician.
If a 13A 3-pin plug is fitted, it must be an ASTA
approved plug, conforming to BS1363 standard.
Replacement 3A fuses must be BSI or ASTA
BS1362 approved.
GUARANTEE
PLEASE KEEP YOUR RECEIPT AS THIS WILL
BE REQUIRED FOR ANY CLAIMS UNDER THIS
GUARANTEE.
• This product is guaranteed for 3 years.
• In the unlikely event of breakdown, please take
it back to the place of purchase, with your till
receipt and a copy of this guarantee.
• The rights and benefits under this guarantee
are additional to your statutory rights which
are not affected by this guarantee.
• Holmes Products Europe undertakes within
the specific period, to repair or replace free of
charge, any part of the appliance found to be
defective provided that:
• We are promptly informed of the defect.
• The appliance has not been altered in any
way or subjected to misuse or repair by a
person other than a person authorised by
Holmes Products Europe.
• No rights are given under this guarantee to a
person acquiring the appliance second hand
or for commercial or communal uses.
• Any repaired or replaced appliance will be
- EARTH
guaranteed on these terms for the remaining
- LIVE
portion of the guarantee.
- NEUTRAL
THIS PRODUCT IS MANUFACTURED TO
COMPLY WITH THE E.E.C. DIRECTIVES
73/23/EEC, 89/336/EEC AND 98/37/EEC.
3
or