After Use - Black & Decker GLC13 Originalanleitung

ENGLISH
Damaged or entangled cords increase the risk of electric
shock.
Where appropriate. When operating an appliance outdoors,
u
use an extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
If operating an appliance in a damp location is
u
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Battery tool use and care (cordless appliance only)
Recharge only with the charger specified by the
u
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
Use appliances only with specifically designated battery
u
packs. Use of any other battery packs may create a risk of
injury and fire.
When battery pack is not in use, keep it away from other
u
metal objects, like paper clips, coins, keys, nails, screws
or other small metal objects that can make a connection
from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the
u
battery; avoid contact. If contact accidentally occurs, flush
with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.

After use

When not in use, the appliance should be stored in a dry,
u
well ventilated place out of the reach of children.
Children should not have access to stored appliances.
u
When the appliance is stored or transported in a vehicle it
u
should be placed in the boot or restrained to prevent
movement following sudden changes in speed or direction.
Service
Have your appliance serviced by a qualified repair person
u
using only identical replacement parts. This will ensure
that the safety of the appliance is maintained.
Additional safety instructions for grass trimmers
+ The following warning symbols are found on the tool:
F Read the manual prior to operation.
Wear safety glasses or goggles when operating this
8 tool.
Keep people and animals at least 6 m away from the
cutting area.
6
R
Do not expose the tool to rain or high humidity.
Be familiar with the controls and the proper use of the tool.
u
Only use the tool in daylight or good artificial light.
u
Before use, check the power supply cord and extension
u
cord for signs of damage, ageing and wear. If a cord
becomes damaged during use, disconnect the cord from
the mains supply immediately. DO NOT TOUCH THE
CORD BEFORE DISCONNECTING THE SUPPLY.
Do not use the tool if the cords are damaged or worn.
u
Wear stout shoes or boots to protect your feet.
u
Wear long trousers to protect your legs.
u
Before using the tool, check that your cutting path is free
u
from sticks, stones, wire and any other obstacles.
Only use the tool in the upright position, with the cutting
u
line near the ground. Never switch the tool on in any other
position.
Move slowly when using the tool. Be aware that freshly cut
u
grass is damp and slippery.
Do not work on steep slopes. Work across the face of
u
slopes, not up and down.
Never cross gravel paths or roads while the tool is running.
u
Never touch the cutting line while the tool is running.
u
Do not put the tool down until the cutting line has come to
u
a complete standstill.
Use only the appropriate type of cutting line. Never use
u
metal cutting line or fishing line.
Be careful not to touch the line trimming blade.
u
Take care to keep the mains cable away from the cutting
u
line. Always be aware of the position of the cable.
Keep hands and feet away from the cutting line at all
u
times, especially when switching on the motor.
Warning! The cutting elements continue to rotate after the
u
tool is switched off.
Never operate the tool with damaged guards or without
u
guards in place.
Always ensure that the ventilation slots are kept clear of
u
debris.
Before using the appliance and after any impact, check for
u
signs of wear or damage and repair as necessary.
Take care against injury from any device fitted for trimming
u
the filament line length. After extending new cutter line
always return the machine to its normal operating position
before switching on.
Do not use the lawn trimmer (edge trimmer), if the cords
u
are damaged or worn.
Keep extension cords away from cutting elements.
u