DeWalt DW733 Anleitung Seite 19

enough free surrounding space around the machine that allows handling of the workpiece
without any restrictions.
To reduce effects of vibration make sure the ambient temperature is not too cold, the machine
and accessories are well maintained and the workpiece size is suitable for this machine.
Switching On and Off (Fig. F1, F2)
The On/Off switch of your DW733 is equipped with a circuit breaker. In case of motor overload,
the power supply to the motor will be cut off. If this happens, turn the machine off and press
the reset button 35 (Fig. F1).
• The workpiece should not be in contact with the cutterhead when switching on.
To turn on, pull the on/off switch 1 up (Fig. F2). The tool now works in continuous operation.
• Allow the motor to reach full speed before feeding the workpiece.
• Allow the blades to cut freely. Do not force.
To switch off, press the on/off switch 1 down.
To lock the machine off, insert a padlock into the hole

WARNING: Always turn off the tool when work is finished and before unplugging.
Planing (Fig. G)

WARNING:
• Remove all foreign objects. Do not plane wood with loose knots. Do not plane wood
that is severely knotted or warped.
• Your DW733 works best with at least one flat surface.
• For optimal results, plane both sides of your workpiece to reach the desired thickness.
Follow the depth of cut and width guidelines shown in the table below
2.5
1.6
0.8
0
20 50 100

WARNING: Feed the workpiece in the direction of the grain (Fig. G).
Snipe
Snipe is a depression made when the ends of the workpiece contact the cutters. To
avoid snipe:
• Make sure the extension tables are level with the main table.
• Keep the workpiece level throughout the planing operation.
• Feed the workpiece flat against the tables.
Warping (Fig. H1–H4)
If your workpiece is only slightly warped, plane both sides to produce the desired thickness.
Bowed Workpieces (Fig. H1, H2)
The feed rollers and cutterhead will temporarily flatten the workpiece (Fig. H1). The bowed
shape, however, will return after planing (Fig. H2).
To remove the bow, use a jointer.
Cupped Workpieces (Fig. H3, H4)
1. Rip the cupped workpiece in the middle (Fig. H3).
2. Plane the pieces separately to eliminate waste.
3. Alternatively, plane the top flat 37 first, then turn the workpiece over and plane the
bottom flat 38 (Fig. H4).
Dust Extraction (Fig. A2, I)

WARNING: Whenever possible, connect a dust extraction device designed in accordance
with the relevant regulations regarding dust emission. The air velocity of externally
connected systems shall be 20 m/s +/- 2 m/s velocity to be measured in the connection
tube at the point of connection, with the tool connected but not running.
1. Mount the dust extraction adaptor
13
2. Insert the reduction bush 40 as shown.
Transporting (Fig. A1, A2)
When transporting your DW733, always carry it by the carrying handles
When transporting or storing your machine, use the cord wrap
36 .
Softwood
Hardwood
150 200 250 300
Width of stock (mm)
using the screws .
39
4 or handholds
to keep the cord in place.
11
MAINTENANCE
Your D WALT power tool has been designed to operate over a long period of time with a
e
minimum of maintenance. Continuous satisfactory operation depends upon proper tool care
and regular cleaning.

WARNING: To reduce the risk of serious personal injury, turn tool off and
disconnect tool from power source before making any adjustments or removing/
installing attachments or accessories. An accidental start-up can cause injury.
Resharpening the Blades
The blades can be resharpened at 42°.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear approved eye protection and approved dust
mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.

WARNING:
• Keep the tables clean and free from grease. Regularly apply some wax to the tables.
• Keep the machine free from dust and shavings.
Before use, carefully check the cutterhead to determine that it will operate properly. Ensure
that dirt, dust or workpiece particles cannot lead to blockage of one of the functions.
In case of workpiece fragments jammed between cutterhead and infeed roller, disconnect the
machine from the power supply and remove the jammed parts.
Optional Accessories

WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should be used with this product.
e
Consult your dealer for further information on the appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked with this symbol must not be
disposed of with normal household waste.
Products and batteries contain materials that can be recovered or recycled reducing
the demand for raw materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at www.2helpU.com.
7 .
EngLIsh
WALT, have not been tested
e
17