Kärcher WPD 100 Advanced Originalbetriebsanleitung Seite 26

1 Bracket
2 Plate
3 Filter
4 Handle
a Remove the filter.
b Insert filter
 Turn the filter to the left until the tab is visible.
 Pull the filter downwards out of the support and re-
move it.
Note:
The used filter can be disposed of as domestic waste af-
ter the water has been drained.
 Wear sterile gloves.
 Unpack the new filter.
 Turn the filter so that the handle is on the left side
and insert it into the relevant support from the bot-
tom.
 Turn the filter to the right all the way to the stop.
1 Bracket
2 Filter
 Check installation position.
The marking on the label on the support and on the
filter must be aligned with each other.
Note:
Filters must be installed in the same position and
must not be interchanged! Observe marking!
 Close device door and insert drip pan.
 Place an receptacle underneath the water outlet.
26
Display
Active-Pure-Filter changed? >or<
Hy-Protect-Flter changed? >or<
Hy-Pure-Filter changed?
>Display YES or NO is flashing<
>changed filter<
Canister under the outlet?
Rinse running 20 l
Note:
During the rinsing process, the receptacle must be emp-
tied several times.
Display
Rinse running >XX< I
>Rinsing interrupted, continue!<
 Empty receptacle.
 Place receptacle on the drip pan.
Display
Rinsing paused, continue!
Rinse running >XX< I
Rinse running 00 l
Filter change
>Finish<
Note:
It is recommended to perform an extraordinary hygieni-
sation after rinsing.
Emptying the drip pan
As soon as the drip pan has reached its maximum filling
level, the message "Empty dripcup" appears on the dis-
play.
 Remove the drip pan.
 Empty the drip pan.
 Check drip pan for soiling and clean as necessary.
 Insert drip pan.
The device is ready for operation again.
The selection water types is shown on the display.
Emptying the can (option)
As soon as the can has reached its maximum filling lev-
el, the message "Empty canister" appears on the dis-
play.
 Open the door on the support leg.
1 Cap with filling level sensor
2 Can
1 Connection drain hose drip pan
2 Cable filling level sensor can
3 Connection drain hose rinsing valve
9
-
EN
 Unscrew the locking cover.
Button
 Remove cap with filling level sensor.
Minus
 Remove and empty can.
 Reinsert the can.
 Fit cap with filling level sensor and tighten.
 Close the door of the base.
Enter
Display
Enter
Drain can emptied?
The device is ready for operation again.
The selection water types is shown on the display.
General information on handling CO
When replacing CO
Button
the gas supplier and any statutory regulations must be
Back (X)
observed.
 The CO bottle must be equipped with a pressure
2
reducer approved by Kärcher, so that the level of
carbonation of the water can be adjusted.
 The food gas carbon dioxide E 290 must comply
Button
with the purity requirements as per directive 96/77/
EG and must be marked as per Art. 7 of the direc-
Enter
tive 89/107/EWG.
 Prior to using a gas bottle, one has to make sure
that the correct gas type has been provided. Only
the hazardous goods label, which must be present
on all gas bottles, can be considered reliable infor-
Back
mation about the type of gas. The colour of the gas
bottle does not always provide clear information re-
garding the gas type. A gas bottle whose content is
questionable or which is abnormal in any other way
(damage, fire damage, signs of mechanical tam-
pering), must not be used.
 Please adher to country-specific regulations.
DANGER
Risk of explosion!
 Do not use CO
for example, marked with a red warning label.
Mortal danger due to possibly bursting CO
 Install and fasten the pressure gas container in an
upright position.
 Never connect the pressure gas container without
pressure reducer and safety valve. The pressure
reducer with safety valve must be approved for the
device type.
Risk of suffocation on account of escaping carbon diox-
ide.
 The installation room must be aerated and ventilat-
ed sufficiently or if a suitable gas warning system
must be installed.
 Do not expose the gas cylinder to direct sunlight.
The gas cylinder must be protected against exces-
sive heating.
 Attach visible marking that points out
the potential presence of gaseous CO
Button
Enter
bottles
2
bottles, the safety instructions of
2
bottle with riser. Riser bottles are,
2
gas tank.
2
.
2