Warranty/Procedure In Case Of Repair; Product Specifications - Ivoclar Vivadent Bluephase Style Gebrauchsinformation

Warranty / Procedure in Case
of Repair
The manufacturer does not accept any liability resulting
from misuse and warranty claims cannot be accepted in
such cases. This is particularly valid for:
– Damage resulting from improper handling, especially
incorrectly stored batteries (see Product Specifications:
Transportation and storage conditions).
– Damage to components resulting from wear under
standard operating conditions (e.g. battery).
– Damage resulting from external influences, e.g. blows,
drop to the floor.
– Damage resulting from incorrect set-up or installation.
– Damage resulting from connecting the unit to a power
supply, the voltage and frequency of which do not
comply with the ones stated on the rating plate.
– Damage resulting from improper repairs or modifica-
tions that have not been carried out by certified Service
Centres.
In case of a claim under warranty, the complete
apparatus (handpiece, charging base, power cord and
power pack) must be returned, carriage paid, to the
dealer or directly to Ivoclar Vivadent, together with the
purchase document. Use the original packaging with the
corresponding cardboard inserts for transportation.
Repair work may only be carried out by a certified Ivoclar
Vivadent Service Centre. In case of a defect that cannot
be rectified, please contact your dealer or your local
Service Centre (see addresses on the reverse side). A
clear description of the defect or the conditions under
which the defect occurred will facilitate locating the
problem. Please enclose this description when returning
the apparatus.

Product Specifications

Light source Ivoclar Vivadent Polywave
Wavelength range 385 – 515 nm
Light intensity 1,200 mW/cm
Operation 3 min on / 7 min off (intermittent)
Light probe 10 mm, black, disinfectable and auto-
clavable
Anti-glare cones autoclavable
Signal transmitter acoustic after 10 seconds and every time the
start button / time selection button is
pressed
Dimensions of the hand- L = 180 mm W = 30 mm H = 30 mm
piece (without light
probe)
Weight of the handpiece 120 g (including battery and light probe)
Operating voltage 3.7 VDC with battery
handpiece 5 VDC with power pack
Operating voltage Charging Base 5 VDC
Power supply Input: 100 – 240 VAC, 50 – 60 Hz 310 mA
Output: 5 VDC / 2 A
Manufacturer Friwo
Type: FW7401M/05
Weight of the power 165 g
supply
Operating conditions Temperature +10 °C to +30 °C
(+50 °F to +86 °F)
Relative humidity 30% to 75%
Ambient pressure 700 hPa to 1060 hPa
Dimensions of the D = 125 mm, H = 70 mm
charging base
Weight of the charging 195 g
base
Charging time Approx. 2 hours (with the battery empty)
Power supply of the Li-Po battery (approx. 20 min. with a new,
handpiece fully charged battery)
Transportation and Temperature –20 °C to +60 °C
storage conditions (+4 °F to +140 °F)
Relative humidity 10% to 75%
Ambient pressure 500 hPa to 1060 hPa
The curing light has to be stored in closed,
roofed rooms and must not be exposed to
severe jarring.
Battery:
– Do not store at temperatures above
40 °C / 104 °F (or 60 °C / 140 °F
for a short period). Recommended storage
temperature 15 – 30 °C (59 – 86 °F).
– Keep the battery charged and store no
longer than 6 months.
Delivery form 1 Charging base with power cord
and power pack
1 Handpiece
1 Light probe 10 mm, black
3 Anti-glare cones
1 Sleeves (50 pcs.)
1 Instructions for Use
LED
®
± 10%
2
15