Technical Data; Maintenance - AEG Powertools US 400 XE Originalbetriebsanleitung

TECHNICAL DATA

Rated input ................................................................. 400 W
Stroke rate under no–load .................................... 0-3500 /min
Lengths of stroke.......................................................... 13 mm
Weight without cable .................................................. 1,7 kg
Noise/Vibration Information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) .......................... 83 dB(A)
Sound power level (K = 3 dB(A)) .............................. 94 dB(A)
Wear ear protection!
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Sawing of wood
Vibration emission value a ................................... 18,3 m/s
h
Uncertainty K ........................................................... 1,5 m/s
WARNING
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 60 745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the
vibration emission may differ. This may signifi cantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should also take
into account the times when the tool is switched off or when it is
running but not actually doing the job. This may signifi cantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the operator from the
effects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
WARNING!
Read all safety warnings and all instructions, including those
given in the accompanying brochure. Failure to follow the
warnings and instructions may result in electric shock, fi re and/or
serious injury. Save all warnings and instructions for future
reference.
SAFETY INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing loss.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting accessory
contacting a „live" wire may make exposed metal parts of the
power tool „live" and could give the operator an electric shock.
Appliances used at many different locations including open air
should be connected via a residual current device of 30 mA or less.
Always wear goggles when using the machine.
It is recommended to wear gloves, sturdy non slipping shoes and
apron.
Sawdust and splinters must not be removed while the machine is
running.
Always disconnect the plug from the socket before carrying out
any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
Always use the protective shields on the machine.
Do not use cracked or distorted saw blades.
Plunge cuts without pre–drilling a hole are possible with soft
materials (wood, light building materials for walls). Harder
materials (metals) must fi rst be drilled with a hole corresponding to
the size of the saw blade.
US 400 XE
When working in walls ceiling, or fl oor, take care to avoid electric
cables and gas or waterpipes.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
SPECIFIED CONDITIONS OF USE
This sabre saw cuts wood, plastic, and metal. It can cut
straight lines, curves, and internal cut-outs. It cuts pipes and
can cut fl ush to a surface.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
2
documents. EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-2,
2
EN 61000-3-3, in accordance with the regulations 98/37/EG,
2004/108/EG
Winnenden, 2009-07-02
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also possible
to connect to sockets without an earthing contact as the design
conforms to safety class II.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type printed
on the label and order the drawing at your local service agents or
directly at: Milwaukee Electric Tool, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before
starting the machine.
Always disconnect the plug from the socket
before carrying out any work on the machine.
Do not dispose of electric tools together with household
waste material! In observance of European Directive
2002/96/EC on waste electrical and electronic
equipment and its implementation in accordance with
national law, electric tools that have reached the end of
their life must be collected separately and returned to
an environmentally compatible recycling facility.
Rainer Kumpf
Manager Product Development
English
7
GB