Herunterladen Diese Seite drucken

TriStar VE-5944 Bedienungsanleitung Seite 7

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 6
wird: docken sie den Ventilator ab und bewahren Sie den Ventilator auf einem trockenen Platz aut.
Dieses Produkt ist. entsprechend, den Radiostörungsforderungen der
Ratsrichtlinien 82/499EEC hergestellt
Der Hersteller haftet in keiner Hinsicht für durch falschen Gebrauch oder
Nachlässigkeit verursachten Unfälle.
EN
Instruction manual for fans
A) PARTS DIAGRAM
1 ) Front guard
2) Spinner
3) Fan-blade
4) Ring
5) Rear guard
6) Clip
7) Rustproof
8) Shaft
9) Motor plastic cover
10) Oscillation knob
11 ) Neck joint
12) Speed switch
A+B) ASSEMBLING INSTRUCTIONS
1. Unscrew the spinner by turning clockwise and the ring by turning counter -clockwise.
2. Mount the rear guard to the motor by matching the holes on the rear guard to the round pins on the motor
housing. Push in firmly until the pins protrude through the holes.
3. Secure the rear guard to motor housing with the ring.
4. Insert the blade onto motor shaft by matching slots in the blade with pin in
ring by turning counter- clockwise.
5. Test blade by rotating with your hand. Make sure there Is no friction with the
otherwise repeat the steps again
6. Mount front guard onto rear guard by inserting the back side of the front guard over rear guard and secure with the
screw supplied and with clips on front guard,
B) ASSEMBLING INSTRUCTIONS STAND FAN
1 First of all, loosen and remove the four screws from bars~ Next cross the bars of the stand. Be sure to align the
four holes on the bars to the fours holes on the bar of the stand. Then tighten the four screws and insert the stand
ornament down over the feet.
2. "Caution". Never remove the extension pipe stopper. lf you remove the extension pipe stopper service may be
necessary. Never loosen the extension pips set screw.
(a) Loosen the screw of the switch housing by turning it to the left.
(b) Now place the hole in the bottom of the switch housing over the extension pipe.
(c) Line up the screw of the switch housing over the hole in the extension pipe and tighten the screw, completely, to the
right.
3, From this point on follow assembling instructions for other models as they are.
C) RULES FOR SAFE OPERATION
1 Use correct voltage.
2. Never insert fingers, pencils, or any other object through the guard when fan is running.
3. Disconnect tan when moving from one location to another.
4. Disconnect tan when removing guards for cleaning.
5. Be sure fan is on a stable surface when operating to avoid overturning.
6. Do not use fan outdoors.. Rain may create electrical hazard.
D) OPERATING INSTRUCTIONS
1. Plug the power cord into a wall outlet (AC 220 Volts- 50 Hz).
2. Oscillation. Push down the oscillation knob and the fan will oscillate. Pull oscillation knob up and the tan will not oscillate
E) GUIDE TO BETTER FAN MAINTENANCE
1. Use in a dry place, free of excessive humidity and water
2. Keep fan clean, Wiper away dirt with a clean cloth;
B) PARTS DIAGRAM
1 ) Front guard
2) Spinneer
3) Fan-blade
4) Plastic-nut
5) Rear guard
6) Clip
7) Motor shaft
8) Clutch knob
9) Adjustment screw
10) Speed control
11) Thumb screw
12) Height adjustment knob
13) Extension pipe
14) Column
15) Stand ornament
16) Four screws
1 7 ) Stand
.
7
shaft and tighten the blade with the
ring. Blade should rotate freely

Werbung

loading