Intended Use - Scheppach 5906808901 Originalbetriebsanleitung

Introduction
MANUFACTURER:
scheppach Fabrikation von
Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
WE RECOMMEND:
Read through the complete text in the operating in-
structions before installing and commissioning the
device.
The operating instructions are intended to help the
user to become familiar with the machine and take
advantage of its application possibilities in accord-
ance with the recommendations.
The operating instructions contain important infor-
mation on how to operate the machine safely, pro-
fessionally and economically, how to avoid danger,
costly repairs, reduce downtimes and how to in-
crease reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country.
Keep the operating instructions package with the
machine at all times and store it in a plastic cover to
protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information. The machine can only
be operated by persons who were instructed con-
cerning the operation of the machine and who are in-
formed about the associated dangers. The minimum
age requirement must be complied with.
In addition to the safety requirements in these oper-
ating instructions and your country's applicable regu-
lations, you should observe the generally recognized
technical rules concerning the operation of wood-
working machines.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Device Description (Fig.1-2)
Base plate
1
Pillar
2
Drilling table
3
Machine head
4
5 Drill chuck
6 Grips
Drill chuck protection
7
Depth stop
8
Motor
9
On-Off switch
10
Belt protective hood
11
12 Locking grip for belt tension
13 Laser on/off switch
13.1 Battery compartment cover
Vice
14
A Hexagonal screw
B
4 mm Allen key
C
3 mm Allen key
D Vice fastening screws
E Drill chuck key
Unpacking
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!

Intended use

The bench drill is designed for drilling in metal, wood,
plastic and tiles. Straight shank drills with a drilling
diameter from 1.5 mm to 16 mm can be used.
The device is intended to be used by do-ityour-
selfers. It was not designed for heavy commercial
use. The tool is not to be used by persons. under the
age of 16. Children over the age of 16 may use the
tool except under supervision. The manufacturer is
not liable for damage caused by an improper use or
incorrect operation of this device. The bench-type
circular saw is designed for the slitting and cross-
cutting of all types of timber, commensurate with the
machine's size. The machine is not to be used for
cutting any type of roundwood.
Notes on safety
m Caution! When using power tools, observe the
following basic safety measures for the prevention of
electric shocks and the risk of injury and fire.
GB І 19