Residual Risks; Technical Data - Scheppach 5906808901 Originalbetriebsanleitung

Safety instructions for handling batteries
Always make sure that the batteries are inserted
1
with the correct polarity (+ and –), as indicated
on the battery.
Do not short-circuit batteries.
2
Do not charge non-rechargeable batteries.
3
Do not overcharge batteries!
4
Do not mix old and new batteries or batteries
5
of different types or manufacturers! Replace an
entire set of batteries at the same time.
Immediately remove used batteries from the
6
device and dispose of them properly! Do
not dispose batteries with household waste.
Defective or used batteries must be recycled ac-
cording to Directive 2006/66 / EC. Give back bat-
teries and / or the device has been offered to the
collective facilities. About disposal facilities you
can inform by your municipal or city government.
Do not allow batteries to heat up!
7
Do not weld or solder directly on batteries!
8
Do not dismantle batteries!
9
Do not allow batteries to deform!
10
Do not throw batteries into fire!
11
Keep batteries out of the reach of children.
12
Do not allow children to replace batteries without
13
supervision!
Do not keep batteries near fire, ovens or other
14
sources of heat. Do not use batteries in direct
sunlight or store them in vehicles in hot weather.
Keep unused batteries in the original packaging
15
and keep them away from metal objects. Do not
mix unpacked batteries or toss them together!
This can lead to a short-circuit of the battery
and thus damage, burns or even the risk of fire.
Remove batteries from the equipment when it
16
will not be used for an extended period of time,
unless it is for emergencies!
NEVER handle batteries that have leaked with-
17
out appropriate protection. If the leaked fluid
comes into contact with your skin, the skin in
this area should be rinsed off under running wa-
ter immediately. Always prevent the fluid from
coming into contact with the eyes and mouth.
In the event of contact, please seek immediate
medical attention.
Clean the battery contacts and corresponding
18
contacts in the device prior to inserting the bat-
teries:

Residual risks

The machine has been built according to the
state of the art and the recognised technical
safety requirements. However, individual residu-
al risks can arise during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
22 І GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
• Residual risks can be minimised if the „safety in-
structions" and the „Proper use" are observed
along with the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the ma-
chine in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be fixed between the clamps.
• Avoid accidental starting of the machine: the op-
erating button may not be pressed when inserting
the plug in an outlet.
• Use the tool that is recommended in this manu-
al. In doing so, your saw provides optimal perfor-
mance.
• Hands may never enter the processing zone when
the machine is in operation. Release the handle
button and switch off the machine prior to any op-
erations.
Prior to any adjustment, maintenance or service
•
work disconnect the mains power plug!

Technical Data

Nominal input voltage
Power rating
Motor speed
Output speed (infinitely
adjustable)
Drill chuck mount
Drill chuck
Dimensions of drill table
Angle adjustment of
table
Drill depth
Pillar diameter
Height
Base area
Weight
Laser class
Wavelength of laser
Laser output
Noise and vibration values
The total noise values determined in accordance
with EN 61029.
sound pressure level L
pA
uncertainty K
pA
sound power level L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Total vibration values (vector sum - three directions)
determined in accordance with EN 61029.
230 V~/50 Hz
500 W (S2 15min)
1450 min
-1
550 -2500 min
-1
B16
1,5 - 16 mm
164 x 162 mm
45°/0°/45°
50 mm
46 mm
590 mm
298 x 190 mm
14,5 kg
II
650 nm
< 1 mW
72,6 dB (A)
3 dB
82 dB (A)
3 dB