Setting Possibilities - Migatronic OMEGA ADVANCED Kurzanleitung

Programs
No: Wire Material Gas Machine
P001 MMA All
P003 Manuel MIG/MAG CO /Mix All
2
P101 Ø 0.8 mm Fe SG2ER70S6 CO All
2
P102 Ø 1.0 mm Fe SG2ER70S6 CO All
2
P103 Ø 1.2 mm Fe SG2ER70S6 CO Omega 400
2
P104 Ø 1.6 mm Fe SG2ER70S6 CO Omega 400
2
P106 Ø 0.6 mm Fe SG2ER70S6 CO All
2
P111 Ø 0.8 mm Fe SG2ER70S6 ArCO (82/18) All
2
P112 Ø 1.0 mm Fe SG2ER70S6 ArCO (82/18) All
2
P113 Ø 1.2 mm Fe SG2ER70S6 ArCO (82/18) Omega 400
2
P114 Ø 1.6 mm Fe SG2ER70S6 ArCO (82/18) Omega 400
2
P116 Ø 0.6 mm Fe SG2ER70S6 ArCO (82/18) All
2
P117 Ø 1.6 mm Fe SG2ER70S6 ArCO (92/8) Omega 400
2
P118 Ø 1.2 mm Fe SG2ER70S6 ArCO (92/8) Omega 400
2
P119 Ø 0.9 mm Fe SG2ER70S6 ArCO (82/18) All
2
P120 Ø 0.9 mm Fe SG2ER70S6 ArCO (92/8) All
2
P193 Ø 1.2 mm Innershield None All
P194 Ø 1.6 mm Innershield None All
P199 Ø 0.9 mm Innershield None All
No: Wire Material Gas Machine
P201 Ø 0.8 mm ER 316 LSI ArCO (98/2) All
2
P202 Ø 1.0 mm ER 316 LSI ArCO (98/2) All
2
P203 Ø 1.2 mm ER 316 LSI ArCO (98/2) Omega 400
2
P311 Ø 0.8 mm AlMg5 ER5356 Ar All
P312 Ø 1.0 mm AlMg5 ER5356 Ar All
P313 Ø 1.2 mm AlMg5 ER5356 Ar All
P314 Ø 1.6 mm AlMg5 ER5356 Ar Omega 400
P352 Ø 1.0 mm AlSi5 ER4043 Ar All
P353 Ø 1.2 mm AlSi5 ER4043 Ar All
P403 Ø 1.2 mm FCW215 FeRutil ArCO (82/18) All
2
P404 Ø 1.6 mm FCW215 FeRutil ArCO (82/18) Omega 400
2
P418 Ø 1.2 mm FCW MC-RS ArCO (82/18) All
2
P423 Ø 1.2 mm FCW115 FeMetal ArCO (82/18) All
2
P424 Ø 1.6 mm FCW115 FeMetal ArCO (82/18) Omega 400
2
P453 Ø 1.2 mm FCW217 FeRutil ArCO (82/18) All
2
P483 Ø 1.2 mm FCW CrNi E316LT-1 ArCO (82/18) Omega 400
2
P501 Ø 0.8 mm CuAl8 Brazing Ar All
P502 Ø 1.0 mm CuAl8 Brazing Ar All
P561 Ø 0.8 mm CuSi3 Brazing Ar All
P562 Ø 1.0 mm CuSi3 Brazing Ar All
501 3733 I
OMEGA ADVANCED

Setting possibilities

Setting Area
Primary parameters:
1 Welding current (MMA) from 15A to max. output
1 Welding current (MIG) Area depends on
program
Wire feed speed (MIG)
Thickness of material (MIG)
2 Arc length -9.9 – +9.9
Secondary parameters:
1 Arc power (MMA) 0 - 150
3 Hotstart (MMA) 0 - 100
1 Inductance (MIG) -5.0 – +5.0
2 Gas pre flow (MIG) 0.0 – 10.0
3 Soft start (MIG) Off / 1.5 – 18.0
4 Hotstart time (MIG) 0.0 – 10.0
5 Slope down (MIG) 0.0 – 10.0
6 Burnback (MIG) 1 – 30
7 Gas post flow (MIG) 0.0 – 10.0
8 DUO Plus TM (MIG) 0 – 50
QUICKGUIDE
UK
Step Factory setting Unit
2T/4T (MIG) Tack (MIG)
1 80 A
1 Depending on program A
0.1 m/min
0.1 mm
0.1 0.0 0.0 V
1 25 %
1 25 %
0.1 0.0 0.0 -
0.1 0.2 0 s
0.1 3 3 m/min
0.1 0.5 0 s
0.1 0.2 0 s
1 5 5 ms
0.1 3 0 s
1 25 25 %