Chamberlain Liftmaster SCS300KS Montageanleitung Seite 14

PLEASE START BY READING THESE IMPORTANT SAFETY RULES • SAVE THESE INSTRUCTIONS
This safety alert symbol means "Caution" - failure to comply with such an instruction involves risk of personal
injury or damage to property. Please read these warnings carefully.
This gate drive mechanism is designed and tested to offer appropriately safe service provided it is installed and
operated in strict accordance with the following safety rules.
Incorrect installation and/or failure to comply with the following instructions may result in serious personal injury
or property damage.
When using tools and small parts to install or
carry out repair work on a gate exercise caution
and do not wear rings, watches or loose
clothing.
Installation and wiring must be in compliance
with your local building and electrical
installation codes. Power cables must only be
connected to a properly earthed supply.
Any entrapment possibility by the moving wing
between wing & walls must be secured with
safety edges or IR-sensors.
Please remove any locks fitted to the gate in order
to prevent damage to the gate.
After the installation a final test of the full
function of the system and the full function of
the safety devices must be done.
This drive cannot be used with a gate
incorporating a wicket door unless the drive
cannot be operated with the wicket door open.
Contents: General advice on
installation and use:
Contents list: page 1
Content of the carton: figure
Before you begin: page 2
Checklist: page 2
Gate types/installation height:
page 2, figure A-F
2
Gate configuration:
3
page 2, figure A-F
Gate stops:
page 2, figure 3 A-F
Assembly measurements and opening
angle: pages 2-3, figures
CONTENT OF THE CARTON
(1) Motor (1 or 2)
(2) Electronic Control (1)
(3) Postbracket (1 or 2)
(4) Keys (2 or 4)
(5) Gate fixing bracket (1 or 2)
(6) Capacitor (1 or 2)
(7) Manual (1)
709228B-GB - 05.2004
Post bracket/Gate fixing bracket:
pages 2-3, figures
Release of drive arms:
1
page 3, figure
Installing the drive arms::
page 3, figure
Wiring: page 3, figure
Maintenance work: page 3
Electrical Installation: + Electronic
Control: page 4, figure
Safety: page 4
A-B
4
1
It is important to make sure that the gate always
runs smoothly. Gates which stick or jam must be
repaired immediately. Employ a qualified
technician to repair the gate, never attempt to
repair it yourself.
Keep additional accessories away from children. Do
not allow children to play with pushbuttons or remote
controls. A gate can cause serious injuries as it
closes.
Disconnect electric power to the system before
making repairs or removing covers.
A disconnecting device must be provided in the
permanently-wired installation to guarantee all-
pole disconnection by means of a switch (at least
3mm contact gap) or by a separate fuse.
Make sure that people who install, maintain or
operate the gate drive follow these instructions.
Keep these instructions in a safe place so that you
can refer to them quickly when you need to.
The full protection against potential squeeze or
entrappment must work direct when the drive
arms are installed.
Flashing Lamp + Antenna:
5
A-D
IR Sensor: page 5, figure
6
Key switch:
7
A-B
Initial setting of Remote control:
9 A-D
Initial Operation: page 6
Technical Data: page 6
8
Replacement Parts: figure
(8) Clevis pin (2 or 4) and Rings (4 or 8)
(9) Nut (1 or 2)
(10) Washer (1 or 2)
(11) 3-Channel Remote Control Mini (1)
(12) IR Sensor (1 pair)
(13) Flashing lamp (1)
(14) Antenna (1)
11 13
page 5, figure A-D +
10
14
page 5, figure A-D
15
page 6, figure
A-B
A-D
16