Listening Through A Receiver; Check Points Before Requesting Service - Samsung LE52F9 Bedienungsanleitung

listening through a receiver

You can listen to sound through a receiver instead of the tV speaker.
1. Press the anynet+ button.
Press the ▲ or ▼ button to select receiver, then press the
enter/oK button.
2. Press the ◄ or ► button to select to on, then press the
enter/oK button.
Now you can listen to sound through the receiver.
. Press the exIt button to exit.
➣
When the receiver is set to On, you can listen to the TV sound
through the 2-channel receiver.
➣
If the receiver is exclusively for a home theatre only (supporting
audio only), it may not appear in the device list.
➣
Only when you have connected the optical jack of the TV and the receiver properly, does Receiver
work.
➣
In case of a content with copyright problem, listening through the receiver may not properly operate.
➣
When listening through the receiver, there are restrictions for using the PIP and audio-related menu.

Check Points before requesting Service

Symptom
anynet+ does not
work.
I want to start
anynet+.
I want to exit anynet+. ■
the Connecting to
anynet+ device...
message appears on
the screen.
the anynet+ device
does not play.
the connected device
is not displayed.
the tV programme
cannot be recorded.
the tV sound is not
output through the
receiver.
Solution
■ Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+
devices only.
■ Connect only one receiver.
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device's Video/Audio/HDMI 1.3 cable connections.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn't work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI 1.3 cable, please make sure to search
devices again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
■ Check if the Anynet+ device is properly connected to the TV and check if the
Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup menu.
■ Press the tV button on the TV remote control to switch to TV. Then press the
Anynet+ button to show the anynet+ menu and select a menu you want.
Select View tV in Anynet+ menu.
■ Press the SourCe button on the TV remote control and select a device other
than Anynet+ devices.
■ Press any of Ch, Ch lISt, Pre-Ch, and such to change to the
TV mode. (Note that the channel button operates only when a tuner-embedded
Anynet+ device is not connected.)
■ You cannot use the remote control when you are configuring Anynet+ or
switching to a view mode.
■ Use the remote control when the Anynet+ setting or switching to view mode is
complete.
You cannot use the play function when Plug & Play is in progress.
■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI 1.3 cable is properly connected.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI
cables may not support Anynet+ functions.
Check whether the antenna jack on the recording device is properly connected.
Connect the optical cable between TV and the receiver.
english - 0
tV P9
View tV
Select Device

record

menu on Device

Device operation

receiver :on

Setup

move
enter
exit