Werbung
Verfügbare Sprachen
Verfügbare Sprachen
- the ON/OFF (2) switch is effective and works with the plug
removed;
- all machine parts are correctly installed and free of damage;
- the ventilation slits (11) are not obstructed.
START AND STOPPING
LH16ES
- Starting: push the slide of the switch (2) forward; if the tool
is to be locked in the ON position, apply pressure to the front
part of the slide switch at the same time;
- Stopping: release the slide or, if locked in position, apply
pressure to the back part of the switch and allow it to return
to the stop position.
WARNING: after power cutout, if the ON/OFF switch is
inserted, it must be released (see Stop).
LH18ENS
- Starting: push the lever of the switch (2) towards the body
of the tool; if the tool is to be locked in the ON position,
press button (9) at the same time and keep it pressed while
releasing lever (2), thus locking the switch.
- Stopping: release the lever of the switch or, if locked in
position, push the lever to release the lock button.
LH22N – LH22EN
- Starting:move the switch lever (2) up; to lock it in "engaged"
position, move the switch block (9) forward towards the
machine body.
- Stopping: release the switch lever (2); if the switch is in
"engaged" position, move the switch lever (2) up in order to
release the switch block (9).
The tool continues to rotate after it is turned off.
SELECTING RPM
The rpm can be adjusted by rotating the wheel (3). The choice
of speed depends on the characteristics of the abrasive disc
and the material to be worked.
ALLOWED ACCESSORIES
Polishing foam and foam support pad up to Ø 200 mm max
(LH16ES: ø 178 mm max)..
NOISE/VIBRATION LEVEL
The equivalent noise pressure level and the mean squared
acceleration are measured according to standard:
EN IEC 62841-2-3
SOUND
PRESSURE
UNCERTAINTY
LEVEL
[dB(A)]
[dB(A)]
L
pA
LH16ES
90.5
LH18ENS
87.0
LH22N
82.0
LH22EN
82.0
Use ear protection!
Displayed emission values are comparative and are to
be employed for a provisional assessment of the
operator's risk exposure during the work period. Appropriate
evaluation of work period must also include tool's idle and stop
10
VIBRATION LEVEL[m/s
SOUND
(polishing)
POWER
LEVEL
On 3 AXIS
K
L
a
wA
h
3
98.5
1.50
3
95.0
1.94
3
93.0
2.50
3
93.0
2.50
periods. These emission values represent the tool's main
applications. If the tool is used for other applications, with
other accessories, or if it does not undergo regular
maintenance, emission values can significantly increase during
operations.
MAINTENANCE
All maintenance operations must be carried out with the power
supply disconnected.
At the end of each work session, or when required, remove any
dust from the body of the tool using a jet of compressed air,
paying particular attention to the motor ventilation slots.
No other maintenance operations must be undertaken by
the user.
Maintenance and cleaning of the inner parts, like brushes,
ball bearings, gears etc. or others, must be carried out only
by an authorized customer-service workshop also available
on the website http://www.rupes.it under Service section. Use
exclusively original RUPES.
DISPOSAL (WEEE DIRECTIVE)
For EU countries only: According to the European
Directive on Waste from electrical and electronic
equipment and its implementation in conformity with
national standards, exhausted electrical equipment must be
collected separately, in order to be recycled in an
environmentally friendly way. The product, when it reaches the
end of its life, must not be dispersed in the environment or
thrown away as household waste. It must be disposed at
authorized recycling centres (contact your local authorities to
know where to dispose of the product according to the law).
The correct disposal of the product contributes to the health
and preservation of the environment.
Illegal disposal of the product will entail penalties against the
offenders.
EU DECLARATION OF CONFORMITY
We declare, under our exclusive responsibility, that the products
described in this manual are in compliance with all applicable
provisions of the directives and regulations listed below:
2006/42/EC; 2014/30/EU; 2011/65/EU
and are in conformity with the following standards:
EN 62841-1:2015 + AC:2015 + A11:2022
EN IEC 62841-2-3:2021 + A11:2021
EN 55014-1:2017 + A11:2020
EN 55014-2:2015
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN 62233:2008 + AC:2008
]
2
EN IEC 63000:2018
UNCERTAINTY
K
1.5
1.5
THE PRESIDENT
1.5
1.5
Technical file at:
RUPES SpA a socio unico
Via Marconi, 3/A - Loc. Vermezzo 20071
VERMEZZO CON ZELO (MI) - Italy
p
S.p.A. a socio unico
G. Valentini
Vermezzo con Zelo (MI), 25/07/2024
Werbung
