Werbung
Verfügbare Sprachen
Verfügbare Sprachen
10.1.1 List of commands Service Standard
protocol
The basic principle of the application is that the
PC (or a terminal) sends an ASCII command (cha-
racter), possibly with additional numeric parame-
ters. In turn, the AEA111/1 sends an appropriate
response (see following table):
Parameter:
19200 baud, no parity, 8 bit, 1
Stop bit, no hand shake
Output:
ASCII (if not otherwise specified)
Value ranges: 2/3 Byte: 0...65535 / 0... +-2
Input:
Capitals and small letters are ac-
cepted.
Output:
All response telegrams are com-
pleted with a CR (=hex13), except
for the "W" command.
Command Length Response Description
A0
2/10 xxxxxxxx> Hardware version
A1
2/7
xxxxx>
A2
2/10 xxxxxxxx> reserved
A3
2/7
xxxxx>
B
1/10 +xxxxxxx> Position value without correction
Ey
2/10 +xxxxxxx> Issue parameters (resolved to 1µm)
Fy+xxxxxxx 10/2
>
H
1/4
K
1/-
M
1/4
xx>
Nxx
3/2
>
Q
2/x
Ry_xxxxxxxx 11/2
S00000
6/2
>
AEA111/1
Datum 25.01.2008
23
Software version
reserved
values
y = adress (0...4)
x = decimal value
y = 0: position value
y = 2: zero position value
y = 3: calibration value
y = 4: extent limit
Enter 3 byte value (resolved to 1µm)
y = address (2...4)
y = 2: zero position value (default = 0)
y = 3: calibration value (default = 0)
y = 4: extent limit (default = 0)
If "0" is set, position value -
96..4000mm is output
x = decimal value (±0...9999999)
for internal purposes: (parameter
data)
Software Reset
send SIKONETZ3 adress (default
= 01)
hand over SIKONETZ3 adress 2-digit
xx = decimal value (01...31)
for internal purposes: (parameter
data)
Enter configuration register with
binary notation
y = 0: Register 0
y = 1: Register 1
_ = Separator
x = 0 or 1
xxxxxxxx = Bit7,6,5...0: Register
content
Set position value to calibration
value
Command Length Response Description
S11100
6/2
>
S00100
6/2
>
S01001
6/2
>
S01002
6/2
>
S01003
6/2
>
S01004
6/2
>
T0
2/2
>
T1
2/2
>
U
1/x
V
1/x
W
1/4
xxxx
X
1/6
0xyy>
Y0
2/6
0xyy>
Y1
2/6
0xyy>
Z
1/10 +xxxxxxx> Absolute position value
10.2 SIKONETZ3 Protocol description
The SIKONETZ3 protocol enables parameterization
and output of position values by the AEA111/1. The
data signals comply with the RS485 standard. Up
to 31 devices may be addressed via bus since an
address is included in each telegram. The address
of each device is factory set to the value "01".
Therfore, first re-program all parameters (counting
direction, calibration value...), particularly the de-
vice address (01...31) via Service standard protocol
(see chapter 10.1) before operating the device on
a bus. following this basic parameterization, seit-
ching over to the SIKONETZ3 protocol and, thus,
bus operation is possible (SW1.2).
The protocol setup follows the Master-Slave-Sys-
tem; the translation module only has the slave
function.
Art.Nr. 84155
set device to original state (de-
fault-setting)
SIKONETZ3 adress: 01
Position value filter: ON
counting direction: POSITIV
SSI Code: Gray
RS485 Start message: no
delete ERROR status
calibration data (zero point value/
calibration value): 0
Start sensor alignment
Deactivate absolute decoding/SSI
(volatile)
(corresponds to configuration in-
put = 24V)
Activate absolute decoding / SSI
(default)
(corresponds to configuration in-
put = 0V)
Position value is monitored in the
"Millimetre jump" mode (volatile)
Position value is monitored in
the "Speed measurement" mode
(default)
Counting direction POSITIV (de-
fault)
counting direction NEGATIV
for internal purposes: (parameter
data)
for internal purposes: (parameter
data)
Absolute position value in binary
code without CR
Output system status register
(hex)
Output configuration register-0
(hex)
Output configuration register-1
(hex)
Änd. Stand 245/07
17
Werbung
