Midi-Datenformat; Format Details; System Exclusive Message - Yamaha O2R96 Bedienungsanleitung

MIDI-Datenformat

1. CHANNEL MESSAGE
Command
8n NOTE OFF
9n NOTE ON
Bn CONTROL CHANGE
Cn PROGRAM CHANGE
2. SYSTEM COMMON MESSAGE
Command
F1 MIDI TIME CODE QUARTER
FRAME
F2 SONG POSITION POINTER
3. SYSTEM REALTIME MESSAGE
Command
F8 TIMING CLOCK
FA START
FB CONTINUE
FC STOP
FE ACTIVE SENSING
FF RESET
Received only when the Automix TIME REFERENCE setting is
MIDI CLOCK.
4. EXCLUSIVE MESSAGE
4.1 Real Time System Exclusive
Command
F0 7F dd 06 MMC COMMAND
F0 7F dd 07 MMC RESPONSE
F0 7F dd 01 MIDI TIME CODE

4.2 System Exclusive Message

4.2.1 Bulk Dump
Command
F0 43 0n 7E BULK DUMP DATA
F0 43 2n 7E BULK DUMP REQUEST rx/tx
The following data types of bulk dump are used on the 02R96.
Data name tx/rx function
'm' tx/rx Scene Memory & Request
'S' tx/rx Setup Memory & Request
'a' tx/rx Automix data & Request
'R' tx/rx Input patch library & Request
'O' tx/rx Output patch library & Request
'H' tx/rx Channel library & Request
'G' tx/rx Gate library & Request
'Y' tx/rx Compressor library & Request
'Q' tx/rx Equalizer library & Request
'E' tx/rx Effect library & Request
'J' tx/rx Bus to Stereo library & Request
'K' tx/rx Surround Monitor library & Request
'P' tx/rx Program change table & Request
'C' tx/rx Control change table & Request
'L' tx/rx User define layer & Request
'I' tx/rx Plug-in User define & Request
'V' tx/rx User define key & Request
'N' tx/rx Plug-in Effect Card Data & Request
rx/tx function
rx Control the internal effects
rx Control the internal effects
rx/tx Control parameters
rx/tx Switch scene memories
rx/tx function
rx Used when TIME REFERENCE is
MIDI CLOCK.
rx Used when TIME REFERENCE is
MIDI CLOCK.
rx/tx function
rx MIDI clock
rx* Start automix (from the
beginning)
rx* Start automix (from the
middle)
rx* Stop automix
rx Check MIDI cable connections
rx Clear running status
rx/tx function
tx MMC command (refer to
MMC specification)
rx MMC response (refer to MMC
specification)
rx Used when TIME REFERENCE is
MTC.
rx/tx function
rx/tx BULK DUMP DATA
BULK DUMP REQUEST
MIDI-Datenformat
4.2.2 PARAMETER CHANGE
Command
F0 43 1n 3E 0B PARAMETER
CHANGE
F0 43 3n 3E 0B PARAMETER
REQUEST
F0 43 1n 3E 7F PARAMETER
CHANGE
F0 43 3n 3E 7F PARAMETER
REQUEST
The following data types of parameter change are used by the 02R96.
Type tx/rx function
1 tx/rx Edit buffer
2 tx/rx Patch data
3 tx/rx Setup data
4 tx/rx Backup data
16 tx/rx Function (recall, store, title)
17 rx Function (pair)
18 rx Function (event)
32 rx Key remote
33 tx/rx remote meter
34 tx/rx remote counter
** tx means that the data can be transmitted from the 02R96. rx means that
the data can be received by the 02R96.

Format Details

1. NOTE OFF (8n)
Reception
Received when the [Rx CH] matches.
Used to control effects.
STATUS 1000nnnn 8n
DATA 0nnnnnnn nn
0vvvvvvv vv
2. NOTE ON (9n)
Reception
Received when the [Rx CH] matches.
Used to control effects.
STATUS 1001nnnn 9n
DATA 0nnnnnnn nn
0vvvvvvv vv
3. CONTROL CHANGE (Bn)
Reception
Received when [Control Change Rx] is ON and the [Rx CH] matches.
However if [OMNI] is ON, this is received regardless of the channel. If
[Control Change ECHO] is ON, these messages are echoed to MIDI OUT.
If [TABLE] is selected, parameters will be controlled according to the set-
tings of the [Control assign table]. The parameters that can be set are de-
fined in the CONTROL CHANGE ASSIGN PARAMETER LIST. If
[NRPN] is selected, four messages are used to control the defined param-
eter: NRPN control numbers (62h, 63h) and DATA ENTRY control num-
bers (06h, 26h). Parameter settings are defined in the CONTROL
CHANGE ASSIGN PARAMETER LIST.
Transmission
If [TABLE] is selected, operating the parameters specified in the [Control
assign table] will cause these messages to be transmitted on the [Tx CH] if
[Control Change TX] is ON. The parameters that can be specified are de-
fined in the CONTROL CHANGE ASSIGN PARAMETER LIST.
If [NRPN] is selected, operating the specified parameters will cause data to
be transmitted on the [Tx CH] if [Control Change TX] is ON, using four
messages: NRPN control numbers (62h, 63h) and DATA ENTRY control
numbers (06h, 26h). Parameter settings are defined in the CONTROL
CHANGE ASSIGN PARAMETER LIST.
279
rx/tx function
rx/tx 02R96-specific parameter
change
rx/tx 02R96-specific parameter
request
rx/tx General purpose digital mixer
parameter change
rx/tx General purpose digital mixer
parameter request
Note off message
Note number
Velocity (ignored)
Note on message
Note number
Velocity (1-127:on, 0:off)
02R96—Bedienungsanleitung