Metabo TPF 18 LTX 2200 Originalbetriebsanleitung Seite 13

6. Initial Operation
6.1 Battery pack
Charge the battery pack before use.
Recharge the battery pack if performance
diminishes.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
Battery packs have a capacity and signal display
(17) (depends on design variant):
- Press the button (18), the LEDs indicate the
charge level.
- The battery pack is almost empty and must be
recharged if one LED is flashing.
6.2 Removing and inserting the battery pack
1. Press locking mechanism (15) and fold open the
protective cover (16) .
2. Slide on the battery pack (14) or remove it.
3. Close the protective cover (16) .
To prevent accidental starting, always insert
the battery pack only after assembly.
The device runs only when the protective cover is
closed.
The ideal storage temperature for battery packs is
between 10°C and 30°C.
Do not reach in the battery pack recess when
inserting the battery pack.
6.3 Storing the battery box (7) during pump
operation
The battery box can be permanently mounted on
the wall for storage near the container, suspended
with the fastening hook (e.g. rain barrel) or
positioned without a hook whilst observing all
specifications.
In any case, do not immerse the battery pack
unit in water and close the battery pack before
each use. Always position the battery pack box in a
dry and safe place!
a) Mounting the fastening hook* (25)
The mounting hooks (26) of the fastening hook (25)
are inserted into the recesses (23) on the underside
of the battery pack box (24) (step 1.) and the hook
(25) is pulled upwards (step 2.) so that it firmly fits in
the recesses. (see fig.D p. 3)
b) Wall fixture battery pack box (7)
On the rear side of the battery pack box there are
two mounting holes with spacing dimensions.
Ensure that the battery box is firmly screwed to the
wall using two suitable screws or hooks and hang it
securely from there.
6.4 Mounting multi-adapter (27)
Screw the multi-adapter (27) onto the pump
connection (6). Hoses with dimensions
can be attached to the multi-adapter.
6.5 Mounting tap connector (28)
(Only TPF 2200)
Screw tap connector (28) onto the pump connection
(6).
6.6 Mounting hose (19)
(Only TPF 2200)
The hose can be connected with the quick coupling
(21) to the tap connector (28).
6.7 Mounting hose (19); maximum flow rate
(Only TPF 7000)
Screw the hose (not included in the scope of
delivery) to the pump connection (6) using a
suitable and matching adapter (not included in the
scope of delivery). Pay attention to the installation
instructions of the respective manufacturer.
For optimum delivery performance, use suitable
adapters and hose lines without reducing the
internal diameter unnecessarily.
A 1 1/2" hose is needed to achieve a flow rate of
7,000l/h. If the hose diameter is less, the flow rate is
reduced accordingly.
7. Use
7.1 Control panel (8) see overview p. 3
1. Activation button:
Briefly pressing the ON/OFF (10) button starts the
pump at the last selected power setting.
2. Change power setting:
Briefly pressing the (11) button switches between
the three power settings (1., 2., 3., back to 1.). The
respective setting is shown by the three green
LEDs.
TPF 2200:
Power setting 1: max 1,200l/h, max. 0.6 bar
Suitable for: Watering with garden sprinkler, light
cleaning work, use of short hoses
Power setting 2: max 1800 l/h, max. 1.3 bar
Suitable for: Irrigation (garden sprinkler)
Power setting 3: max 2200 l/h, max. 2.2 bar
Suitable for: Drainage with long hoses, garden
irrigation with surface sprinklers
TPF 7000:
Power setting 1: max.3,900 l/h, max. 0.3 bar
Suitable for: Water with garden sprinkler, drainage,
use of short hoses
Power setting 2: max. 5,600 l/h, max. 0.6 bar
Suitable for: Drainage, light cleaning work
Power setting 3: max. 7,000 l/h, max. 0.9 bar
Suitable for: Drainage
3. Timer function (only TPF 2200):
3
/ " and 1"
4
Timer function (LED blue)
The pump has a selectable timer function, e.g. for
targeted use of garden sprinklers.
During the operation of the pump, the automatic
timer function can be selected after 5/10/20 minutes
ENGLISH en
13